21
Instructions concerning safety
Keep instructions for use near the machine, so that it is
always possible for the operator to operate the machine
correctly.
Do not pull the filter out of the machine if the filtering
process has not yet finished. After the filtering process is
over, please be aware of idle running of the unit: danger
of scalding.
Only use the glass jug for hot drinks. Do not clean with
hard devices. Do not use for cooking beverages. Not
suitable for use in micro-wave oven.
Do not heat up the jug if empty or wash in dish washer
at a temperature of over 92°C.
Do not hold the full jug above persons.
Do not touch the warm holders. Risk of burning!
Switch off the warm holders as soon as the glass jugs are
empty.
Melitta SystemService is not liable for damages which
occur due to lack of maintenance, improper handling of the
machine, or installation of parts which are not genuine
Melitta parts.
Melitta SystemService reserves the right to carry out
alterations at any time without prior notice if these
alterations are necessary for technical improvement.
Prior to opening the machine pull the plug out of the
socket.
Switch off the water supply on site if the machine is not
to be operated for a longer period of time.
The machine must not be operated outdoors.
Conditions of guarantee
We guarantee for the perfect working of this machine / installa-
tion over a period of 12 months beginning at date of invoice.
If assembly is performed by us or a company authorized by
us then warranty beginning is date of assembly. Throughout
this period all defects due to faulty material, poor design, and
faulty construction work will be repaired free of charge by us,
provided that the machine was operated and maintained
properly. Parts which have to be exchanged remain property of
MSS and are to be made available to us.
We are not responsible for damages caused by lack of
maintenance and care even if they occur during the period of
guarantee. Damages caused by unauthorized or improper repair
work or installation of not genuine Melitta spare parts are also
not covered by this guarantee. All parts made of porcelaine or
glass or wearing parts are also excluded from our guarantee
Wearing parts are: sealings/gaskets, valves, faucets, heating
resistors, coat of lacquer, switches and thermostates/thermo-
regulators. Claims for damages under conditions of guarantee
can only be accepted if a written report has been handed in
by our customer service and an inspection of the machine has
taken place in our work.
Instructions for eliminating possible faults/defects
Fault/Defect Cause Elimination
Servicing indicator lamp (1) Excessive build-up of limescale in instantenous
Descale machine at the end of the
starts to burn, water heater filtering process
filtering process is interrupted Temperature control defective Request service engineer
Water supply line to heater is clogged Clense the tubes and sieves
Defective switch Request service engineer
Retarded filtering process See above mentioned
Very fine ground coffee, very soft water = Choose coarser ground brand of
filter pores clog up coffee
Water dosing not according to Machine is not on an even surface = Even out uneven patches of the sur-
selected programme the water level in the fresh water container face beneath the machine, change
is not as indicated position of the machine
Water pressure is not correct
Check water pressure and adjust by
means of valve/pressure pump
Solenoid valve dirty Request service engineer
Coffee does not taste good High rate of chlorine in water
Inform Melitta service personnel to install
water filter
Contains residual descaling or dish washing agent
Rinse machine or jug with water
Coffee has been stored for more than one hour
Consume fresh coffee as soon as
possible
Poor quality of the supplied coffee powder Speak with coffee supplier
Coffee too cold No lid on the jug Insert lid on jug
Coffee too hot
Small quantity of coffee has been kept in the
Consume freshly filtered coffee as
machine too long soon as possible
HW-unit 193 W / 197 W Temperature limiter has responded Remove cap (16), press in the limiter
does not heat up situated beneath the cap, request for
service engineer
HW valve does not close, drips Limescale in closing area of valve Operate switch several times
Request service engineer
Please contact MSS service personnel if other faults/defects than the above mentioned occur.
To Next Page
Loading...
