Member's Mark 720-0582

Questions and Answers

R
Robert MasonAug 12, 2025
Why does my Member's Mark Grill only heat to 200-300 degrees?
- D
  duncanloganAug 12, 2025
  Your Member's Mark grill might not be reaching higher temperatures due to several reasons. Check if the fuel hose is bent or kinked, ensure the grill area is free of dust, and verify the burner and orifices are clean. Also, inspect for any spider webs or insects that may be obstructing the gas flow. The regulator may have been triggered, restricting gas flow. To reset it, turn off all burners, close the LP tank valve, disconnect the regulator, wait one minute, reconnect, slowly open the LP tank valve fully, and then light all burners.
A
Amanda JuarezAug 16, 2025
How to fix Member's Mark 720-0582 that will not light immediately?
- V
  Vincent EvansAug 16, 2025
  If your Member's Mark Grill doesn't light immediately, ensure you have a spark while trying to light the burner. If there's no spark, check that the wire is connected to the electrode assembly. Clean the wire(s) and/or electrode with rubbing alcohol and a clean swab, then wipe with a clean cloth. Check if the other burners operate; if so, inspect the gas orifice on the malfunctioning burner for any obstructions.
J
Jocelyn Gillespie MDAug 20, 2025
What to do if rotisserie burner will not light on Member's Mark 720-0582?
- M
  Michelle CruzAug 20, 2025
  If the rotisserie burner on your Member's Mark Grill won't light, check for debris blocking the electrode. Verify there is a spark jumping to the burner from the electrode; if not, check the battery inside the ignition box. Also, check to ensure the gas is on.
W
wbeardAug 23, 2025
What to do if my Member's Mark 720-0582 takes a long time to preheat?
- N
  Nicole VelezAug 25, 2025
  A normal preheat for your Member's Mark Grill to reach 500-600 degrees should take about 10-15 minutes. Cold weather and wind can increase this time. Also, using volcanic rock or briquettes can extend the preheat time and affect the maximum temperature.
D
donaldtoddAug 27, 2025
Why is my Member's Mark 720-0582 Grill regulator making noise?
- L
  Leslie WilliamsAug 28, 2025
  The noise from the regulator on your Member's Mark Grill could be due to a plugged vent hose or a faulty regulator. Ensure the vent hole on the regulator is not obstructed. Clear the hole, close the gas control valves, wait ten minutes, and restart. Check your flames for proper performance; if they are not correct, replace the regulator.
N
Nicholas MasonAug 31, 2025
What to do if burner flames are not light blue on Member's Mark 720-0582 Grill?
- C
  Christina WrightAug 31, 2025
  If the burner flames on your Member's Mark Grill are not light blue, it could be due to insufficient air intake. Elevation is the primary cause, but cold weather can also affect the mixture. Burner adjustment may be required. Also, check if the grill is in a windy location.
S
Sergio StewartSep 4, 2025
What to do if rotisserie motor will not turn on Member's Mark 720-0582 Grill?
- G
  Gary JohnsonSep 4, 2025
  If the rotisserie motor on your Member's Mark Grill won't turn, ensure it's connected to a properly grounded power supply and that the on/off switch is in the 'on' position. Also, make sure the spit is fully inserted into the rotisserie motor, the load doesn't exceed the 40-pound capacity, and there's no obstruction or drag.
D
Daniel CainSep 7, 2025
What to do if full size cover does not fit the Member's Mark 720-0582?
- E
  eduardo48Sep 7, 2025
  If the full-size cover doesn't fit your Member's Mark Grill, it might be the incorrect cover for your grill model, or it could be a tight fit. Ensure the cover is the correct length by measuring it from left to right and comparing it to the grill's measurement. Compare the location and size of the hood portion of the cover to your grill. Try spreading the cover and allowing it to relax, preferably in warm sunlight or a warm room. For grills with a side shelf, bunch the cover like a sock and put it on from left to right.