Need help?Do you have a question about the Memmert SE 200 and is the answer not in the manual?
Explains the meaning of symbols used in the operating instructions and on the unit.
Provides essential safety guidelines for operating the equipment and handling loads.
Summarizes technical data including ambient conditions, temperature ranges, and safety devices.
Details electrical requirements, specifications, and safety precautions for connecting the unit.
Details the use of stainless steel for casing and its properties.
Outlines methods for setting up the cabinet on a floor or table, including clearances.
Describes how to mount the unit on a wall using specific brackets and fixing screws.
Explains how to stack two ovens of the same size on top of each other.
Guides the user through the initial setup and crucial checks before the first use of the oven.
Describes the main switch, status lamps, and the fresh air control slider.
Explains the function and different settings of the fresh air control slider for ventilation.
Details the operation of the digital rotary knob and set-button for temperature and program settings.
Provides key operational tips, including how to set values and store them.
Explains how to set temperature, fan operation, and program sequences using the controller.
Offers an important note regarding PC operation via serial interface and parameter alteration.
Defines the communication protocol and explains PC connection via serial interface.
Details the RS232C interface for PC operation and software usage.
Describes how to use the rotary knob and set-button for inputting values and settings.
Details setting temperature, delay, hold time, loop, SP, and fan status for programmes.
Shows how to program a switch-off delay triggered by reaching a specific set temperature.
Demonstrates programming a delayed start and a subsequent fixed hold time.
Illustrates programming a delay, hold time, and loop function for repeated operation cycles.
Details programming complex sequences involving delay, hold, loop, and temperature dependency.
Notes that 'FA' indicators are specific to cabinets equipped with a fan.
Explains how to access current values and setpoints during program execution.
Describes display indicators for program completion and methods for restarting the unit.
Details the adjustable overheat controller (TWW) for protection against excessive temperatures.
Advises on setting the safety device sufficiently higher than the maximum working temperature.
Explains setting the temperature limiter for cabinet/environment and load protection.
Provides a table with recommended loading levels for optimal temperature distribution.
Describes the use of the apparatus for sterilizing medical materials using dry heat.
Provides directives, examples, and preparation guidelines for hot air sterilization procedures.
Provides specific instructions and notes for working with sterilising cassettes.
Warns about the door closure mechanism on models 700/800 and handling of the key.
Illustrates a sterilization program for the SLE 600 model at 180°C for 1 hour 30 minutes.
Explains how the door remains locked during sterilization and unlocks upon power failure.
Provides general recommendations for servicing, including lubrication of moving parts.
Details the procedure for readjusting the oven door and its locking plate.
Emphasizes the importance of regular cleaning for maintaining oven performance and appearance.
A troubleshooting guide listing common faults, their causes, and solutions.
Advises on contacting the Memmert service department for unlisted malfunctions.
Provides the contact address and general information for Memmert GmbH + Co. KG.
States that the dimensions provided are subject to confirmation.
Confirms conformity of the product with the European Electromagnetic Compatibility Directive.
Confirms conformity of the product with the European Low Voltage Directive.
States product compliance with the European Medical Device Directive.
Confirms Incubator conformity with the European Electromagnetic Compatibility Directive.
Confirms Incubator conformity with the European Low Voltage Directive.
Defines technical terms such as nominal temperature, ambient temperature, and steady-state condition.
Explains the meaning of symbols used in the operating instructions and on the unit.
Provides essential safety guidelines for operating the equipment and handling loads.
Summarizes technical data including ambient conditions, temperature ranges, and safety devices.
Details electrical requirements, specifications, and safety precautions for connecting the unit.
Details the use of stainless steel for casing and its properties.
Outlines methods for setting up the cabinet on a floor or table, including clearances.
Describes how to mount the unit on a wall using specific brackets and fixing screws.
Explains how to stack two ovens of the same size on top of each other.
Guides the user through the initial setup and crucial checks before the first use of the oven.
Describes the main switch, status lamps, and the fresh air control slider.
Explains the function and different settings of the fresh air control slider for ventilation.
Details the operation of the digital rotary knob and set-button for temperature and program settings.
Provides key operational tips, including how to set values and store them.
Explains how to set temperature, fan operation, and program sequences using the controller.
Offers an important note regarding PC operation via serial interface and parameter alteration.
Defines the communication protocol and explains PC connection via serial interface.
Details the RS232C interface for PC operation and software usage.
Describes how to use the rotary knob and set-button for inputting values and settings.
Details setting temperature, delay, hold time, loop, SP, and fan status for programmes.
Shows how to program a switch-off delay triggered by reaching a specific set temperature.
Demonstrates programming a delayed start and a subsequent fixed hold time.
Illustrates programming a delay, hold time, and loop function for repeated operation cycles.
Details programming complex sequences involving delay, hold, loop, and temperature dependency.
Notes that 'FA' indicators are specific to cabinets equipped with a fan.
Explains how to access current values and setpoints during program execution.
Describes display indicators for program completion and methods for restarting the unit.
Details the adjustable overheat controller (TWW) for protection against excessive temperatures.
Advises on setting the safety device sufficiently higher than the maximum working temperature.
Explains setting the temperature limiter for cabinet/environment and load protection.
Provides a table with recommended loading levels for optimal temperature distribution.
Describes the use of the apparatus for sterilizing medical materials using dry heat.
Provides directives, examples, and preparation guidelines for hot air sterilization procedures.
Provides specific instructions and notes for working with sterilising cassettes.
Warns about the door closure mechanism on models 700/800 and handling of the key.
Illustrates a sterilization program for the SLE 600 model at 180°C for 1 hour 30 minutes.
Explains how the door remains locked during sterilization and unlocks upon power failure.
Provides general recommendations for servicing, including lubrication of moving parts.
Details the procedure for readjusting the oven door and its locking plate.
Emphasizes the importance of regular cleaning for maintaining oven performance and appearance.
A troubleshooting guide listing common faults, their causes, and solutions.
Advises on contacting the Memmert service department for unlisted malfunctions.
Provides the contact address and general information for Memmert GmbH + Co. KG.
States that the dimensions provided are subject to confirmation.
Confirms conformity of the product with the European Electromagnetic Compatibility Directive.
Confirms conformity of the product with the European Low Voltage Directive.
States product compliance with the European Medical Device Directive.
Confirms Incubator conformity with the European Electromagnetic Compatibility Directive.
Confirms Incubator conformity with the European Low Voltage Directive.
Defines technical terms such as nominal temperature, ambient temperature, and steady-state condition.
General| Frequency | 50/60 Hz |
|---|---|
| Interior Material | Stainless steel |
| Voltage | 230 V |
| Timer | 0-99 hours 59 minutes |
| Safety Features | Over-temperature protection |
To Next Page
