Need help?Do you have a question about the Memmert UE 200 and is the answer not in the manual?
Explains safety symbols, general instructions, transport precautions, and operational warnings.
Details electronic controllers, timer, and RS232 interface for Memmert cabinets.
Describes cabinet fan operation via controls or PC.
Summary of technical specs: ambient conditions, temp ranges, safety devices.
Explains overheat controller (TWW) and temperature limiter (TWB).
Details electrical requirements, power, voltage, weight, and material quality for ovens.
Highlights use of stainless steel for casing, emphasizing stability and hygiene.
Provides guidelines for cabinet placement, clearances, and air circulation.
Details specifications for wall mounting ovens using available brackets.
Instructions for stacking ovens, including mounting.
Guides on initial setup, checking sensors, and handling the oven door.
Explains main switch positions: off, continuous, and programmed operation.
Details the fresh air control slider and its ventilation level settings.
Describes controller operation via rotary knob and set-button, and its display.
Explains setting temperature and controlling fan on/off.
Details operating/programming cabinets using MEMMERT software via PC.
Defines the communication protocol according to NAMUR standards.
Explains connecting cabinets to a PC using the serial interface and RS232C.
Describes the effect of turning the rotary knob for setting values.
Explains actions when set-button is not actuated vs. actuated.
Instructions for programming a switch-off delay.
Instructions for programming switch-off delay dependent on set temperature.
Example of programming a cabinet to start heating after a delay.
Example of programming delayed start and shutdown after operation time.
Example of programming delayed start/shutdown based on reaching set temperature.
Example of programming delayed start, cool-down, and repeating the pattern.
Example of programming delay, hold, cool-down repeat with temperature dependency.
Details on accessing actual values and setpoints during program operation.
Describes program termination and unit restart procedures.
Instructions for adjusting TWW for cabinet/environment or load protection.
Instructions for adjusting TWB for cabinet/environment or load protection.
Emphasizes air circulation via proper loading, shelf placement, and avoiding tight packing.
Table of recommended loading levels for different oven models.
Describes use of apparatus for sterilizing medical materials with dry heat.
Provides directives for hot air sterilization: preparation and temp/time selection.
Guidance on using sterilising cassettes: air flow, packing, and closing.
Example program for sterilizing SLE 600 at 180°C for 1h 30min.
Explains the function of the door interlock locking doors during sterilization.
Recommends lubrication and qualified service for malfunctions.
Details how to readjust the door hinge and locking plate for tight closing.
Guidelines for cleaning cabinet interior and exterior using stainless steel cleaner.
Checklist to identify and rectify common faults via indicator lamps and display errors.
Provides company address, contacts, and safety-approved test marks.
Company address and contact details.
Declaration of conformity with European EMC Directive 89/336/EEC.
Declaration of conformity with European Low Voltage Directive 73/23/EEC.
Declaration of conformity for sterilisers with EU medical products directive (93/42/EWG).
Company address and contact details.
Declaration of conformity with European EMC Directive 89/336/EEC.
Declaration of conformity with European Low Voltage Directive 73/23/EEC.
Explains safety symbols, general instructions, transport precautions, and operational warnings.
Details electronic controllers, timer, and RS232 interface for Memmert cabinets.
Describes cabinet fan operation via controls or PC.
Summary of technical specs: ambient conditions, temp ranges, safety devices.
Explains overheat controller (TWW) and temperature limiter (TWB).
Details electrical requirements, power, voltage, weight, and material quality for ovens.
Highlights use of stainless steel for casing, emphasizing stability and hygiene.
Provides guidelines for cabinet placement, clearances, and air circulation.
Details specifications for wall mounting ovens using available brackets.
Instructions for stacking ovens, including mounting.
Guides on initial setup, checking sensors, and handling the oven door.
Explains main switch positions: off, continuous, and programmed operation.
Details the fresh air control slider and its ventilation level settings.
Describes controller operation via rotary knob and set-button, and its display.
Explains setting temperature and controlling fan on/off.
Details operating/programming cabinets using MEMMERT software via PC.
Defines the communication protocol according to NAMUR standards.
Explains connecting cabinets to a PC using the serial interface and RS232C.
Describes the effect of turning the rotary knob for setting values.
Explains actions when set-button is not actuated vs. actuated.
Instructions for programming a switch-off delay.
Instructions for programming switch-off delay dependent on set temperature.
Example of programming a cabinet to start heating after a delay.
Example of programming delayed start and shutdown after operation time.
Example of programming delayed start/shutdown based on reaching set temperature.
Example of programming delayed start, cool-down, and repeating the pattern.
Example of programming delay, hold, cool-down repeat with temperature dependency.
Details on accessing actual values and setpoints during program operation.
Describes program termination and unit restart procedures.
Instructions for adjusting TWW for cabinet/environment or load protection.
Instructions for adjusting TWB for cabinet/environment or load protection.
Emphasizes air circulation via proper loading, shelf placement, and avoiding tight packing.
Table of recommended loading levels for different oven models.
Describes use of apparatus for sterilizing medical materials with dry heat.
Provides directives for hot air sterilization: preparation and temp/time selection.
Guidance on using sterilising cassettes: air flow, packing, and closing.
Example program for sterilizing SLE 600 at 180°C for 1h 30min.
Explains the function of the door interlock locking doors during sterilization.
Recommends lubrication and qualified service for malfunctions.
Details how to readjust the door hinge and locking plate for tight closing.
Guidelines for cleaning cabinet interior and exterior using stainless steel cleaner.
Checklist to identify and rectify common faults via indicator lamps and display errors.
Provides company address, contacts, and safety-approved test marks.
Company address and contact details.
Declaration of conformity with European EMC Directive 89/336/EEC.
Declaration of conformity with European Low Voltage Directive 73/23/EEC.
Declaration of conformity for sterilisers with EU medical products directive (93/42/EWG).
Company address and contact details.
Declaration of conformity with European EMC Directive 89/336/EEC.
Declaration of conformity with European Low Voltage Directive 73/23/EEC.
General| Type | Universal Oven |
|---|---|
| Interior Material | Stainless steel |
| Voltage | 230 V |
| Frequency | 50/60 Hz |
| Temperature Uniformity | ± 1 °C |
| Temperature Fluctuation | ± 0.5 °C |
| Heating Method | Convection heating |
| Controller | Digital controller |
| Volume | 200 L |
| Temperature Control | Microprocessor PID control |
To Next Page
