ENGLISHen
10
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool's operation. If damaged, have
the power tool repaired before use. Many acci-
dents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or in case of a power cut.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Smaller workpieces must be secured such that they
are not carried along with the drill bit when drilling
(e.g. by clamping in a vice or on a work bench with
screw clamps).
Keep hands away from the rotating tool! Remove
chips and similar material only with the machine at
standstill.
Metabo S-automatic safety clutch. When the safety
clutch responds, switch off the machine immedi-
ately! If the tool jams or catches, the power supply
to the motor is restricted. Due to the strong force
which can arise, always hold the machine with both
hands using the handles provided, stand securely
and concentrate.
The Metabo S-automatic safety clutch must not be
used for torque control.
Caution with hard screwdriving (driving of screws
with either a metric or an imperial thread into steel)!
The head of the screw may rip off or high restoring
torques may be incurred at the handle.
Additional Warnings:
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
...... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
W ......... watts
~.......... alternating current
n
0
......... no-load speed
rpm ...... revolutions per minute
.../min... revolutions per minute
Illustrations are provided at the beginning of the
operating instructions.
Symbol explanation:
Normal drilling/Drill bit
Impact drilling
Movement direction
Driving screws/Screw
Slow
Fast
Fig. A
1 Thumb-wheel for gear selection
2 Additional handle/Additional handle with
vibration damping *
3. Special Safety Instructions
4. Symbols on the tool
5. Figures
6. Overview
WARNING
To Next Page
Loading...
Need help?
General
Weight and Dimensions
