P341/EN AD/F43 Update Documentation
(AD) -24
MiCOM P341
CLI1 Minimum: -9999…+9999
CLI1 Maximum: -9999…+9999
CLI1 Alarm: Disabled/Enabled
CLI1 Alarm Fn: Over/Under
CLI1 Alarm Set: CLI1 min…CLI1 max
CLI1 Alarm Delay: 0.0…100.0s
CLI1 Trip: Disabled/Enabled
CLI1 Trip Fn: Over/Under
CLI1 Trip Set: CLI1 min…CLI1 max
CLI1 Trip Delay: 0.0…100.0s
CLI1 I< Alarm (4…20 mA input only):
Disabled/Enabled
CLI1 I< Alm Set (4…20 mA input only):
0.0…4.0mA
CLI2/3/4 as CLI1
Current Loop Output
CLO1 Output 1: Disabled/Enabled
CLO1 Output Type:
0 - 1mA
0 - 10mA
0 - 20mA
4 - 20mA
CLO1 Set Values: Primary/Secondary
CLO1 Parameter: As shown below*
CLO1 Min: Range, step size and unit
corresponds to the selected parameter
CLO1 Max: Same as CLO1 Min
CLO2/3/4 as CLO1
Current Loop Output Parameters
Current Magnitude:
IA Magnitude
IB Magnitude
IC Magnitude
IN Derived Mag: 0.00…16.0
I Sen Mag: 0.00… 2.0A
Phase Sequence Components:
I1 Magnitude
I2 Magnitude
I0 Magnitude:
0.00…16.0A
Phase Currents:
IA RMS*
IB RMS*
IC RMS*
0.00…16.0A
P-P Voltage Magnitude:
VAB Magnitude
VBC Magnitude
VCA Magnitude
0.0…200.0V
P-N Voltage Magnitude:
VAN Magnitude
VBN Magnitude
VCN Magnitude
0.0…200.0V
Neutral Voltage Magnitude:
VN1 Measured Mag
VN Derived Mag
0.0…200.0V
Phase Sequence Voltage Components:
V1 Magnitude*
V2 Magnitude
V0 Magnitude
0.0…200.0V
RMS Phase Voltages:
VAN RMS*
VBN RMS*
VCN RMS*
0.0…200.0V
Frequency: 0.00…70.0Hz
3 Phase Watts*: -6000W…6000W
3 Phase Vars*: -6000Var…6000Var
3 Phase VA*: 0…6000VA
3Ph Power Factor*: -1…1
Single Phase Active Power:
A Phase Watts*:
B Phase Watts*:
C Phase Watts*:
-2000W…2000W
Single Phase Reactive Power:
A Phase Vars*:
B Phase Vars*:
C Phase Vars*
-2000Var…2000Var
Single Phase Apparent Power:
A Phase VA*:
B Phase VA*:
C Phase VA*
0…2000VA
Single Phase Power Factor:
Aph Power Factor*
BPh Power Factor*
CPh Power Factor*
-1…1
3 Phase Current Demands:
IA Fixed/Roll/Peak Demand*
IB Fixed/Roll/Peak Demand*
IC Fixed/Roll/Peak Demand*
0.00…16.0A
3ph Active Power Demands:
3Ph W Fix/Roll/Peak Demand*
-6000W…6000W
3ph Reactive Power Demands:
3Ph Vars Fix/Roll/Peak Dem*
-6000Var…6000Var
Thermal Overload: 0.00…200.0%
CL Input 1-4: -9999…9999.0
Note 1: Measurements marked with an
asterisk, the internal refresh rate is
nominally 1s, others are 0.5 power
system cycles or less.
Note 2: The polarity of Watts, Var and power
factor is affected by the measurements
Mode setting.
Note 3: These settings are for nominal 1A and
100/120V versions only. For other
versions they need to be multiplied
accordingly.
To Next Page
Loading...
