EasyManua.ls Logo

Midea DLCERAA12AAK User Manual

Midea DLCERAA12AAK
72 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Specifications subject to change without notice.
DLCERA
SERVICE MANUAL
Outdoor Unit Single Zone Ductless System − Sizes 09 to 24
TABLE OF CONTENTS
PAGE
SAFETY CONSIDERATIONS 1.............................
INTRODUCTION 1.......................................
MODEL/SERIAL NUMBER NOMENCLATURES 2.............
SPECIFICATIONS 3.......................................
DIMENSIONS 5.........................................
CLEARANCES 8.........................................
ELECTRICAL DATA 9....................................
WIRING 9...............................................
CONNECTION DIAGRAMS 10.............................
WIRING DIAGRAM 10....................................
REFRIGERATION CYCLE DIAGRAMS 14....................
REFRIGERANT LINES 15.................................
SYSTEM EVACUATION AND CHARGING 16.................
ELECTRONIC FUNCTIONS 17.............................
TROUBLESHOOTING 21..................................
OUTDOOR UNIT DIAGNOSTIC GUIDES 22..................
PCB DIAGRAMS 23......................................
DIAGNOSIS AND SOLUTION 25...........................
DISASSEMBLY INSTRUCTIONS 46.........................
APPENDIX 69...........................................
SAFETY CONSIDERATIONS
Installing, starting up, and servicing air−conditioning equipment can be
hazardous due to system pressures, electrical components, and
equipment location (roofs, elevated structures, etc.).
Only trained, qualified installers and service mechanics should install,
start−up, and service this equipment.
Untrained personnel can perform basic maintenance functions such as
cleaning coils. All other operations should be performed by trained
service personnel.
When working on the equipment, observe precautions in the literature
and on tags, stickers, and labels attached to the equipment.
Follow all safety codes. Wear safety glasses and work gloves. Keep
quenching cloth and fire extinguisher nearby when brazing. Use care in
handling, rigging, and setting bulky equipment.
Read this manual thoroughly and follow all warnings or cautions included
in literature and attached to the unit. Consult local building codes and
National Electrical Code (NEC) for special requirements. Recognize safety
information. This is the safety−alert symbol
!
!
. When you see this symbol
on the unit and in instructions or manuals, be alert to the potential for
personal injury. Understand these signal words: DANGER, WARNING,
and CAUTION.
These words are used with the safety−alert symbol. DANGER
identifies the most serious hazards which will result in severe personal
injury or death. WARNING signifies hazards which could result in
personal injury or death. CAUTION is used to identify unsafe practices
which may result in minor personal injury or product and property
damage. NOTE is used to highlight suggestions which will result in
enhanced installation, reliability, or operation.
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal
injury or death.
Before installing, modifying, or servicing system, main
electrical disconnect switch must be in the OFF
position. There may be more than 1 disconnect switch.
Lock out and tag switch with a suitable warning label.
EXPLOSION HAZARD
Failure to follow this warning could
result in death, serious personal injury,
and/or property damage.
Never use air or gases containing
oxygen for leak testing or operating
refrigerant compressors. Pressurized
mixtures of air or gases containing
oxygen can lead to an explosion.
!
WARNING
CAUTION
!
EQUIPMENT DAMAGE HAZARD
Failure to follow this caution may result in equipment
damage or improper operation.
Do not bury more than 36 in. (914 mm) of refrigerant pipe
in the ground. If any section of pipe is buried, there must be
a 6 in. (152 mm) vertical rise to the valve connections on
the outdoor units. If more than the recommended length is
buried, refrigerant may migrate to the cooler buried section
during extended periods of system shutdown. This causes
refrigerant slugging and could possibly damage the
compressor at start−up.
INTRODUCTION
This Service Manual provides the necessary information to service, repair,
and maintain the outdoor units. Section 2 of this manual has an appendix
with data required to perform troubleshooting. Use the Table of Contents
to locate a desired topic.

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Midea DLCERAA12AAK and is the answer not in the manual?

Midea DLCERAA12AAK Specifications

General IconGeneral
TypeSplit Air Conditioner
RefrigerantR32
Energy Efficiency Ratio (EER)3.21
Power Supply220-240V, 50Hz
Air Flow (High)550 m³/h
Noise Level (Indoor)38 dB(A)
Cooling Capacity12000 BTU/h

Summary

Safety Considerations

General Safety Warnings

Critical safety warnings for electrical shock, explosion, and equipment damage during operation and servicing.

Specifications

Clearances

Electrical Data and Wiring

Electrical Data Tables

Presents key electrical parameters like MCA, MOCP, RLA, and FLA for different unit models.

Diagrams and System Information

Refrigerant Lines

System Evacuation and Charging

Vacuum Pump Procedures

Detailed steps for evacuating the system using vacuum pumps, including deep and triple evacuation methods.

Operational Logic and Control

Troubleshooting and Diagnostics

Troubleshooting Safety Precautions

Essential safety guidelines, including capacitor discharge, before performing diagnostic checks.

Outdoor Unit Diagnostic Codes

A guide to error codes displayed by the outdoor unit and their corresponding LED status for fault identification.

EEPROM and Communication Errors

Diagnosing and resolving EEPROM parameter errors (E0/F4) and communication errors (E1).

Sensor and Fan Speed Errors

Troubleshooting procedures for fan speed control issues (E3/F5) and temperature sensor circuit faults (E4/E5/F1/F2/F3).

Refrigerant Leak and Overload Protection

Diagnosing refrigerant leakage (EC) and overload current protection (F0) issues.

Voltage, IPM, and Compressor Protection

Troubleshooting voltage issues (P1), IPM malfunctions (P0), and compressor protection (P2, P4).

Component Testing Procedures

Methods for testing temperature sensors, compressor windings, IPM continuity, and fan motors.

Disassembly Instructions

Related product manuals