Midea YD1539T - User Manual

Warning notices: Before using this product, please read this manual carefully and keep it for future reference.
The design and specifications are subject to change without prior notice for product improvement.
Consult with your dealer or manufacturer for details.
The diagram above is just for reference. Please take the appearance of the actual product as the standard.
YD1539T
USER MANUAL
Water Dispenser

Summary

Thank You Letter

Safety Instructions

Intended Use

Guidelines to prevent risks and damage from unsafe operation of the appliance.

Explanation of Symbols

Explains signal words and symbols used to indicate hazards and important information.

Danger: Risk of Fire;Flammable Materials

Warning about storing flammable materials and disconnection procedures for safety.

Caution: Risk of Injury

Highlights safety for children and persons with reduced abilities, and intended use cases.

General Warnings

Covers critical warnings about cord damage, ventilation, positioning, water jets, immersion, and altitude.

Specifications

Product Overview

Product Diagram and Labels

Identifies and labels the various components and parts of the water dispenser.

Accessories

Product Installation

Getting Started and Placement

Initial steps for locating the dispenser and ensuring proper placement for safe operation.

Water Bottle Installation

Step-by-step guide for installing the water bottle and initial water dispensing.

Electrical Connection

Instructions for connecting the power supply and verifying the power pilot lamp.

Activating Heating and Cooling Functions

How to activate the heating and cooling features and understand indicator lights.

Securing the Appliance

Instructions on how to fix the machine to prevent instability and avoid hazards.

Operation Instructions

Operation Panel Indicators

Explains the meaning and function of the heating and cooling indicator lights.

Dispensing Cold Water

Detailed steps on how to dispense cold water from the dispenser tap.

Dispensing Hot Water

Detailed steps on how to dispense hot water from the dispenser tap.

Cleaning and Maintenance

Cleaning and Draining Procedure

Step-by-step guide for cleaning the dispenser and draining water safely.

Sanitizing the Machine

Recommended procedure and frequency for disinfecting the water dispenser.

Removing Mineral Deposits

Method for removing mineral build-up using citric acid.

Troubleshooting

Trademarks, Copyrights and Legal Statement

Disposal and Recycling

Environmental Disposal Instructions

Guidance on compliance with WEEE directive and proper recycling of electronic waste.

RoHS Directive Compliance

Statement of compliance with the RoHS Directive regarding restricted materials.

Packaging Material Information

Details about the recyclability of product packaging materials.

Data Protection Notice

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

This document is the user manual for the Midea YD1539T Water Dispenser, providing comprehensive information on its function, specifications, usage, and maintenance.

Function Description

The Midea YD1539T is a water dispenser designed to provide both hot and cold water. It operates by heating and cooling bottled pure water, making it suitable for household and similar applications such as staff kitchen areas, offices, farmhouses, hotels, motels, bed and breakfast establishments, and catering services. The appliance is intended for indoor use only and is designed for expert or trained users in light industry and on farms, or for commercial use by lay persons. It features separate taps for hot and cold water, with indicator lights to show when heating or cooling is in progress. The unit requires a bottled water supply, which is vertically inserted into a bottle supporter on top of the machine.

Important Technical Specifications

• Product Model: YD1539T
• Rated Voltage: 220-240V~
• Rated Frequency: 50/60Hz
• Rated Power: 500W
• Heating Power: 420W
• Cooling Current: 1.0A
• Hot Water Capacity: 4L/h (≥85°C)
• Cold Water Capacity: 0.6L/h (≤15°C)
• Operating Environment Temperature: 10°C-43°C
• Operating Environment Humidity: < 90%
• Altitude Recommendation: Not recommended for use in areas above 1,500m altitude.

Usage Features

The water dispenser is designed for straightforward operation.

• Installation: The dispenser should be placed upright on a flat surface, at least 20cm from a wall, ensuring ventilation openings are not obstructed. It must be connected to a properly grounded wall outlet. The manual emphasizes that the outlet must be connected to a ground wire before plugging in the power cord.
• Water Bottle Installation: To install a water bottle, the label should be removed, and the bottle vertically inserted into the bottle supporter. It's crucial to ensure water runs out from the hot water tap before plugging in the power cord or activating the heating switch to prevent damage.
• Activating Heating & Cooling: The unit will not dispense hot or cold water until the respective switches on the back are activated. Once the power cord is plugged in and the power switch is on, the cooling and heating pilot lamps will illuminate when their functions are active. The heating function takes approximately 15 minutes for the first use, while cooling takes about 2 hours.
• Dispensing Water:
  • Cold Water: Position a container below the cold water tap and depress the button downward to start the flow. Release the button when the desired fill level is reached.
  • Hot Water: For hot water, a safety feature requires sliding a red switch left to the bottom before pushing the hot water button downward to start the flow. Release the button when the desired fill level is reached.
• Safety: The manual highlights several safety instructions, including warnings against storing explosive substances, ensuring proper ventilation, and avoiding modifications to the appliance. It also warns about the risk of burns from hot water (approximately 85°C). The appliance must be fixed in accordance with instructions to avoid instability.

Maintenance Features

Regular cleaning and maintenance are essential for the longevity and safe operation of the water dispenser.

• Power Disconnection: Always cut off the power supply and unplug the dispenser before any cleaning or maintenance operations.
• Initial Cleaning: The machine is disinfected at the factory, but it's recommended to clean it prior to installing the first full bottle of water.
• Cleaning and Draining:
  1. Ensure the power switch is off and the dispenser is unplugged.
  2. Insert a bottle into the supporter.
  3. Open the taps to let about 3 liters of water flow into a container.
  4. Remove the water bottle.
  5. Place a large bucket beneath the drain outlet, remove the drain cover, and allow water to drain.
  6. Replace the drain cover after draining.
• Sanitizing: The machine should be disinfected with a suitable disinfectant according to its instructions, followed by cleaning with water. This process should generally be performed every three months.
• Removing Mineral Deposits:
  1. Mix 4 liters of water with 200g citric acid crystals.
  2. Inject the mixture into the machine, ensuring it can flow out of the hot water tap.
  3. Switch on the power and heat for about 10 minutes.
  4. After 30 minutes, drain off the liquid and clean the machine with water two or three times. This process should be done every six months.
• Professional Service: The manual advises against disassembling the machine by oneself to avoid damage or danger. For cleaning tubes or removing scale, professional institutions and operations are recommended, especially if hard water is used, which can lead to furring or damage to the hot pot or pipeline.
• Troubleshooting: A troubleshooting section provides common problems, possible reasons, and solutions, such as waiting for water to become available, connecting the plug, replacing empty or broken bottles, cleaning the bottle supporter inlet, and ensuring a stable installation surface.

Midea YD1539T Specifications