EasyManua.ls Logo

MikroTik hAP ac lite User Manual

MikroTik hAP ac lite
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
RouterBOARD hAP ac lite
Quick Setup Guide and Warranty Information
The hAP is a simple home wireless access point. It is configured out of the box, you can simply plug in your internet
cable and start using wireless internet. We recommend you to set up a password to secure your device, follow
these steps
Connecting
1. Connect your Internet cable to port 1, and local network PCs to ports 2-5
2. Set your computer IP configuration to automatic (DHCP)
3. Wireless “access point” mode is enabled by default, connect to the wireless network name which starts
with “MikroTik”. Log into your router and configure a the Wireless password and router password to secure
your wireless network and access to the router
4. Default IP address from the local network is 192.168.88.1, open this address in your web browser to start
configuration. The username is admin and there is no password
5. The Ether5 port suports PoE output for powering other RouterBOARD devices. The port has auto detection
feature, so you can connect Laptops and other non-PoE devices without damaging them. The PoE on
Ether5 outputs approximately 2V below input voltage, and supports up to 0.58A (So provided 24V PSU will
provide 22V/0.58A output to the Ether5 PoE port).
Powering
The board accepts powering from the power jack or from the first Ethernet port (Passive PoE):
direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug)
accepts 8-30V DC
first Ethernet port accepts passive Power over Ethernet accepts 8-30V DC
The power consumption under maximum load can reach 5W
Booting process
Initial connection has to be done via the Ethernet cable. Open 192.168.88.1 in your web browser. The username is
admin and there is no password. In case IP connection is not available, Winbox can be used to connect to the
MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup In case you
wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device
when starting it until the LED light turns off, and unit will start to look for Netinstall servers.
Extension Slots and Ports
Five individual 10/100 Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so
you can use either straight or cross-over cables for connecting to other network devices.
Integrated Wireless 2.4GHz and 5GHz 802.11a/b/g/n/ac, simultaneous dual band radio with onboard PIF
antennas, max gain 1.5dBi
Buttons and Jumpers
RouterBOOT reset button (RESET, front panel) has three functions:
o Hold this button during boot time until LED light starts flashing, release the button to reset
RouterOS configuration (total 5 seconds)
o Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10
seconds)
See www.routerboard.com for more information. Contact support@mikrotik.com 11-Dec-15
Question and Answer IconNeed help?

Do you have a question about the MikroTik hAP ac lite and is the answer not in the manual?

MikroTik hAP ac lite Specifications

General IconGeneral
Flash memory16 MB
Internal memory64 MB
DC-in jackYes
USB 2.0 ports quantity1
Ethernet LAN (RJ-45) ports5
Networking standardsIEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ethernet LAN data rates10, 100 Mbit/s
Maximum data transfer rate733 Mbit/s
AC input voltage10 V
Power consumption (max)8 W
Operating temperature (T-T)-30 - 70 °C
Antenna type-
Antenna gain level (max)2 dBi
InternalNo
PlacementTable, Wall
Product colorWhite
Harmonized System (HS) code85176990
Weight and Dimensions IconWeight and Dimensions
Depth28 mm
Width113 mm
Height89 mm

Summary

Connecting

Ether5 Port PoE Output

Ether5 port supports PoE output for powering other devices, with auto detection.

Powering

Powering Options

Device accepts power via jack or first Ethernet port (Passive PoE), supporting 8-30V DC.

Booting Process

Initial Connection and Configuration

Connect via Ethernet, access 192.168.88.1 in browser, use Winbox if IP fails.

Extension Slots and Ports

Ethernet Ports

Five 10/100 Ethernet ports with auto MDI/X for flexible cable connection.

Integrated Wireless Capabilities

Dual-band 2.4GHz and 5GHz 802.11a/b/g/n/ac wireless with onboard PIF antennas.

Buttons and Jumpers

RouterBOOT Reset Button Functions

The reset button has functions for OS reset, CAPs mode, and Netinstall server search.

Operating System Support

Copyright and Warranty Information

Hardware Warranty

MikroTik warrants RouterBOARD equipment for twelve (12) months from shipping date against defects.

RMA Procedure

Procedure for returning failed units to MikroTik for repair or warranty claims.

Federal Communication Commission Interference Statement

FCC Compliance

Equipment complies with FCC Rules Part 15, designed to prevent harmful interference.

Radio Frequency Radiation Exposure

Maintain 13 cm distance for FCC radiation exposure limits for population/uncontrolled environments.

Industry Canada Compliance

IC Compliance

Device complies with Industry Canada licence-exempt RSS standard(s).

Declaration of Conformity

Multi-language Declarations

Statements of conformity to Directive 1999/5/EC in multiple languages.

Instruction Manual Links

Links to instruction manuals in various languages for device configuration.

Related product manuals