Mindray BeneView T8 Quick Guide

Mindray BeneView T8

20 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #8 background image

Loading...

Page #8 background image

6

Basic Operations

Display Screen

1 2

3

4

5

9

6

Patient Information Area

Alarm Symbols

Technical Alarm Area

1.

2.

3.

4. Physiological Alarm Area

5. Waveform Area

6. Parameter Area A

7. Parameter Area B

8. Prompt Message Area

9. QuickKeys area

Select screen items by pressing them direct-

ly on the patient monitor’s screen. You can

enable or disable touchscreen operation

by pressing and holding the [Main Menu]

QuickKey for 3 seconds. A padlock symbol

is displayed if touchscreen operation is

disabled.

Using the Touchscreen

8

7

Other manuals for Mindray BeneView T8

Service Manual234 pages

Operation Manual290 pages

Questions and Answers:

V
Veronica WilcoxAug 21, 2025
How to fix a Mindray Medical Equipment patient monitor that fails to start?
- J
  Joseph GomezAug 21, 2025
  If your Mindray Medical Equipment patient monitor fails to start and neither the AC nor battery LED lights up, check the following: * Ensure the AC mains are properly connected and the battery has sufficient capacity. * Verify the cables from the power switch & LED board to the button board, from the button board to the main board, and from the power module to the main board are correctly connected and undamaged. * If the issue persists, the power switch & LED board, the power module, or the mother board may be defective and require replacement. For power supply protection issues, refer to section 4.6.9 Power Supply Failures.
K
Kelly WellsSep 2, 2025
Why can't I view other patients on my Mindray Medical Equipment?
- K
  Kimberly SmithSep 2, 2025
  If your Mindray Medical Equipment is connected to a LAN but cannot view other patients in View Others mode, check that the LAN cable connection is correct and the cable is not longer than 50m. Note that a patient monitor can only be viewed by 4 other patient monitors at the same time in this mode, so excessive view requests will be ignored. Also, check for IP address conflicts and reconfigure the IP address if needed. Finally, the iView assembly may be faulty and need replacement.
K
Kathy FrancoSep 1, 2025
How to resolve poor print quality on Mindray Medical Equipment?
- R
  Ronald FrankSep 1, 2025
  To resolve poor print quality or paper feeding issues on your Mindray Medical Equipment, first stop the recorder and reinstall the paper roll correctly. Then, check the thermal print head and paper roller for any foreign matter and clean the thermal print head with an appropriate cleaning solution. If the problem persists, the print head or the recorder itself may be defective and require replacement.
P
Phillip ShafferAug 30, 2025
What causes the buttons on my Mindray Medical Equipment to stop working?
- C
  Corey SpencerAug 30, 2025
  If the buttons on your Mindray Medical Equipment are not working, first check that the cable between the button board and the motherboard is properly connected and undamaged. If the cable is secure, the button board itself may be defective and require replacement.
C
Carolyn ArmstrongAug 29, 2025
Why does my Mindray Medical Equipment have frequent dropouts and network disconnects?
- L
  lorijonesAug 29, 2025
  Frequent dropouts and network disconnects in Mindray Medical Equipment can be caused by an incorrect LAN cable connection. Ensure the LAN cable is properly connected and is no longer than 50 meters. Also, check for IP address conflicts and reconfigure the IP address if necessary.
E
Emily Gordon PhDAug 27, 2025
What to do if the integrated display is blank on my Mindray Medical Equipment?
- C
  Christopher ZavalaAug 28, 2025
  If the integrated display on your Mindray Medical Equipment is blank but the monitor still works, check that the cables from the display to the motherboard and from the backlight board to the button board/display are correctly connected and undamaged. If the connections are secure, the backlight board, power module, or the display itself may be defective and require replacement.
L
Lauren SteeleAug 26, 2025
Why does the program upgrade fail on my Mindray Medical Equipment?
- M
  Miguel RiceAug 27, 2025
  If the program upgrade fails on your Mindray Medical Equipment, consider these potential causes: * Ensure you are using the correct network connection (not the iView network connector) and that the hub or switch is functioning correctly, with properly connected network cables. * Verify that the upgrade package is a .pkg file and is selected according to system requirements. * Configure a fixed IP address in range C as specified for the patient monitor. It's recommended to avoid upgrading the program when the patient monitor is connected to a network with multiple PCs.
C
Christopher DrakeAug 25, 2025
Why is my Mindray Medical Equipment not printing?
- A
  Alex HernandezAug 25, 2025
  If your Mindray Medical Equipment is not printing, check the following: * Verify the recorder module is enabled in the [Factory Maintenance>>] menu, and check if the recorder status LED lights. * Ensure the paper roll is installed correctly. * Check that the cable between the recorder and the motherboard is properly connected and undamaged. * Confirm that the power module outputs 5 V DC and 12V DC correctly. * If the issue persists, the recorder itself may be defective and require replacement.
R
Robin WilsonAug 23, 2025
What to do if there is no alarm sound but the alarm lamp is lit on my Mindray Medical Equipment?
- N
  nmartinezAug 23, 2025
  If your Mindray Medical Equipment's alarm lamp is lit but there's no sound, first, check if the audio alarm is disabled. To enable it, go to [Main Menu]?[Maintenance >>]?[User Maintenance >>]?enter the required password? [Alarm Setup >>], and in the popup menu, set [Minimum Alarm Volume] to an appropriate setting. Also, in the [Others] window of the [Alarm Setup] menu, set [Alm Volume] to an appropriate setting. Then check that the cable between the speaker and the motherboard is properly connected and undamaged. If the problem persists, consider that there may be an FPGA audio logic error, speaker failure, or motherboard failure, which may require an upgrade of the audio logic part of the FPGA program or replacement of the speaker or motherboard.

Mindray BeneView T8 Specifications

General

Touchscreen	Yes
Battery Life	Up to 4 hours (depending on usage)
Connectivity	Wi-Fi
Monitoring Parameters	ECG, SpO2, NIBP
Display Type	LED Backlight
Battery Type	Lithium-ion battery

Related product manuals

Preview: Mindray BeneVision N22

Mindray BeneVision N22

Mindray BeneVision N19

Preview: Mindray BeneVision TM80

Mindray BeneVision TM80

Preview: Mindray VS-900

Preview: Mindray iPM Series

Mindray iPM Series

Preview: Mindray MEC-1000

Mindray MEC-1000

Preview: Mindray VS-800

Preview: Mindray iPM-9800

Mindray iPM-9800

Preview: Mindray VS 8