Minebea CSD-903-EX - Page 136

120
Address Data name
1827～53248 UNUSED
53249 BRAND NUMBER
53250～56832 UNUSED
56833 OPERATION MODE
56834 UNUSED
56835～56836 SCALE INTERVAL SETTING
56837～56838 WEIGHING CAPACIT
Y
SETTING
56839～56840 WEIGHT MASS SETTING
56841～56842 REGISTER ZERO POINT LOAD CELL OUTPUT VALUE
56843～56844 REGISTER SPAN POINT LOAD CELL OUTPUT VALUE
56845 ACTUAL WEIGHT CALIBRATION STABILITY CONFIRMATION
56846 ACTUAL WEIGHT CALIBRATION REGISTER ZERO POINT
56847 ACTUAL WEIGHT CALIBRATION REGISTER SPAN POINT
56848 CALIBRATION FINISH
56849 ZERO POINT FINE ADJUSTMENT
56850 SPAN POINT FINE ADJUSTMENT
56851～56852 POINT 1 WEIGHT
56853～56854 POINT 2 WEIGHT
56855～56856 POINT 3 WEIGHT
56857～56858 FINE ADJUSTMENT MODE, LOAD DISPLAY
56859～57344 UNUSED
57345～57346 F-01 DIGITAL FILTER SETTING
57347～57348 F-02 ANALOG FILTER SETTING
57349～
573450
UNUSED
57351～57352 F-04 DISPLAY TIMES
57353～57354 F-05 STABILIZING FILTER SETTING
57355～57356 F-06 STABILIZING FILTER DATA WIDTH
57357～57358 F-07 STABILIZING FILTER TIME WIDTH
57359～57360 F-08 KEY LOCK 1
57361～57362 F-09 KEY LOCK 2
57363～57364 F-10 STABILITY DETECTION DATA WIDTH
57365～57366 F-11 STABILITY DETECTION TIME WIDTH
57367～57372 UNUSED
57373～57374 F-15 OPERATING CONDITION OF PRESET TARE WEIGHT CANCELLATION
57375～57376 F-16 PRINT OPERATION
57377～57378 F-17 HOLD OPERATION
57379～57380 F-18 HOLD TARGET
57381～57382 F-19 SELECTION OF SUB DISPLAY SECTION
57383～57384 F-20 4-STEP COMPARATOR BRAND SETTING TARGET
57385～57386 F-21 4-STEP COMPARATOR OPERATION TARGET
57387～57388 F-22 4-STEP COMPARATOR OPERATION CONDITIONS
57389～57390 F-23 4-STEP COMPARATOR S0 OPERATION
57391～57392 F-24 COMPARATOR HYSTERESIS OPERATING CONDITIONS
57393～57394 F-25 COMPARATOR HYSTERESIS DATA WIDTH
57395～57396 F-26 COMPARATOR HYSTERESIS TIME WIDTH
57397～57402 UNUSED
57403～57404 F-30 BCD OUTPUT OPERATION MODE
57405～57406 F-31 BCD OUTPUT TARGET
57407～57408 F-32 BCD OUTPUT LOGIC
57409～57410 F-33 BCD PC WIDTH
57411～57412 F-34 BCD OUTPUT TIMES
57413～57416 UNUSED
57417～57418 F-37 SI/F PRINT OPERATION
57419～57422 UNUSED
57423～57424 F-40 RS232C OPERATION MODE (Reference use)
57425～57426 F-41 RS-232C/422/485 OUTPUT TARGET (Valid if F-40 = 1 to 4 for RS-232C, F-49 for
RS-422/485) (Reference use)
57427～57428 F-42 RS-232C/422/485 COMMUNICATION SPECIFICATION (Reference use)
57429～57430 F-43 RS-422/485 ADDRESS SETTING (Reference use)
57431～57432 F-44 RS-422/485 CHANGEOVER (Reference use)
57433～57434 F-45 RS-485 REPLY DATA DELAY TIME (Reference use)
57435～57436 F-46 RS-232C/422/485 TRANSMISSION DATA DECIMAL (Reference use)
57437～57438 F-47 STANDARD RS-485 OPERATION (Reference use)
57439～57440 F-48 STANDARD RS-485 OUTPUT TARGET (Reference use)
57441～57442 F-49 RS-422/485 OPERATION MODE (Reference use)
57443～57444 F-50 ACCUMULATION FUNCTION OPERATING CONDITIONS
57445～57446 F-51 TARGET OF BRAND CHANGEOVER