Minebea CSD-903-EX User Manual

DIGITAL INDICATOR
CSD-903-EX
Instruction Manual
EN294-1492-H

Minebea CSD-903-EX Specifications

General

Surface Hardness	7H
Size	9 inches
Resolution	800 x 480
Interface	USB
Operating Temperature	-20°C to +70°C
Storage Temperature	-30°C to +80°C

Summary

FOR SAFE OPERATION

1. LOCATION OF INSTALLATION

Details environmental conditions and places to avoid for instrument installation.

3. INSTRUCTIONS FOR USE

Guidelines and cautions for operating the instrument correctly.

3. OPERATION

3-1. CHANGEOVER OF MODE

4. CALIBRATION

4-1. SET ITEMS REQUIRED IN THE CALIBRATION

Lists the necessary items and parameters for performing calibration.

4-2. PROCEDURE SET IF NECESSARY AFTER CALIBRATION

4-3. CALIBRATION PROCEDURES

Provides a step-by-step guide for performing the calibration process.

4-4. FINE ADJUSTMENT OF ZERO AND SPAN

Explains how to fine-tune zero and span settings for accurate measurements.

4-5. DIGITAL LINEARIZE.

Describes the digital linearization function to reduce measurement errors.

4-6. CALIBRATION ONLY OF ZERO POINT

Details the procedure for re-calibrating only the zero point.

4-7. LOCK OF CALIBRATION

5. C FUNCTION MODE

5-1. SETTING METHOD OF C FUNCTION DATA

Describes the procedure for setting C function data to enable various functions.

5-2. FUNCTION OF C FUNCTION DATA

Details the functions and their corresponding settings for C function data.

6. VARIOUS FUNCTIONS BY C FUNCTION DATA

6-7. ZERO SET

6-8. ZERO TRACKING

6-9. POWER ON ZERO

6-10. TARE WEIGHT CANCELLATION

7. FUNCTION MODE

7-1. SETTING METHOD OF THE FUNCTION MODE

Guides on how to set the function mode by selecting function numbers.

7-2. FUNCTION OF THE FUNCTION DATA

Provides a table detailing functions, numbers, setting values, and contents.

9. MEASUREMENT MODE

9-1. SETTING METHOD OF THE MEASUREMENT MODE

Guides on setting the measurement mode and selecting SQ functions.

9-2. MEASUREMENT COMPARISON VALUE SETTING MODE

Describes how to set measurement comparison values for different modes.

9-3. SIMPLE COMPARISON MODE

Explains the simple comparison mode, including batching and discharging.

9-4. SEQUENTIAL MODE

Details the sequential mode for controlling measurement sequences.

9-5. 4 STEPS COMPARATOR MODE 1

Explains the 4 steps comparator mode 1 for comparing measured values.

9-6. 4 STEPS COMPARATOR MODE 2

Details the 4 steps comparator mode 2 for sorting measurements based on value ranges.

9-8. SETTING METHOD OF THE SQ FUNCTION MODE

Guides on setting the SQ function mode and selecting SQ function numbers.

9-9. FUNCTION OF SQ FUNCTION DATA

Provides a table of SQ function data, settings, and contents.

10. VARIOUS FUNCTIONS BY SQ FUNCTION DATA

12. CHECK MODE

12-1. SETTING METHOD OF CHECK MODE

12-2. EZCTS MODE

15. MODBUS COMMUNICATION

15-1. CALIBRATION BY TRANSMISSION THROUGH MODBUS INTERFACE

Describes the calibration process using Modbus interface transmission.

16. OPTIONS

16-1. ANALOG OUTPUT

Details the specifications and connection for analog output options.

16-2. BCD OUTPUT

Explains the specifications, operation modes, and logic of BCD output.

16-3. RS-232C AND RS-422/485 INTERFACE

17. TROUBLE SHOOTING

17-1. EXECUTE TROUBLE SHOOTING

Provides a flowchart for troubleshooting common issues with the instrument.

18. SPECIFICATIONS

18-1. ANALOG SPECIFICATIONS

Lists the technical specifications for analog output, including current and voltage.

18-2. SPECIFICATIONS FOR DIGITAL

Details the specifications for digital displays, sub-displays, and condition indicators.

18-3. INTERFACE

19. ERROR DISPLAY

19-1. ERROR LOAD DISPLAY

Explains various error codes and their meaning for load display issues.

19-2. ERROR SUB DISPLAY

Details error codes that appear in the sub display.

20. DISPLAY OF SEQUENCE ERROR

25. SETTING TABLE FOR FUNCTIONS