Minelab X-Terra 305 - Getting Started Guide Manual

For complete product specication and operational guidance,
read the full length user manual at www.minelab.com.
WARRANTY TERMS
Please refer to www.minelab.com/warranty-conditions
for full warranty terms and conditions. Register your product
warranty online at register.minelab.com
COMPLIANCE
Information to the User (FCC Part 15.105)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
NOTE: Class B Devices
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help
Warning: Any changes or modications not expressly approved
by Minelab Electronics could void the user’s authority to operate
this equipment.
Australia & Asia Pacic
+ 61 8 8238 0888
minelab@minelab.com.au
Europe & Russia
+353 21 423 2352
minelab@minelab.ie
North, South & Central America
+1 630 401 8150
minelab@minelab.com
Middle East & Africa
+971 4 254 9995
minelab@minelab.ae
Minelab®, X-TERRA™ are trademarks of Minelab Electronics Pty. Ltd. Images and graphics are for illustration purposes only; product conguration
and specications may vary from those shown. Please refer to the product manual for detailed operational guidance.
4901-0267-1 EN
Specications
X-TERRA 305
Discrimination Patterns 1, 2 & All Metal
Discrimination Scale 12
Operating Frequencies (kHz) Change coil to change frequency 7.5 & 18.75
Audio Speaker and Headphone Output
Battery 4 x AA
Standard Coil 9" Concentric 7.5 kHz (Waterproof)
Minelab Electronics,
PO Box 35, Salisbury South
South Australia 5106
2
2
3
3
4
1
1
3
4
1
2
3
1
2
4
Getting Started Guide
Assembly | Follow the steps to put together your X-TERRA 305
2. Assemble shafts
1. Loosen the twistlocks by rotating them
counter-clockwise.
2. Press the spring loaded pin in the lower shaft
and slide it into the middle shaft until the pin
reaches the adjustment holes. The pin will click
into place.
3. Attach the middle shaft to the upper shaft in
the same way.
4. Lock the position of the shafts by rotating
twistlocks clockwise.
3. Attach armrest/stand
1. Place the armrest onto the top of the upper
shaft. Position the armrest just below your
elbow, then line up the boss in the armrest
with the nearest hole in the shaft.
2. Insert the screw through the stand, upper shaft
and armrest. Tighten the screw carefully.
3. With the velcro side facing upwards, thread
the armrest strap through both slots in the
armrest. Ensure the end of the strap will be
fastened outwards from your arm.
1. Attach coil to lower shaft
1. Insert the two rubber washers into the holes
on either side of the yoke.
2. Slide the yoke into the yoke bracket on top of
the coil.
Ensure that the spring loaded pin in the lower
shaft is underneath.
3. Insert the plastic bolt through the yoke and the
yoke bracket.
4. Fasten with the plastic bolt - Do not
overtighten.
4. Connect control box & coil
1. Push the control box onto the end of the
handle until it ts into place.
2. Wrap the coil cable around the lower and
middle shaft enough times to take up the
slack.
3. Use the velcro tabs provided to secure the coil
cable against the shaft.
4. Align the coil connector and plug into the
socket in the back of the control box, lightly
tightening the retaining ring.
Audio
X-TERRA 305 detectors have an external
loudspeaker for detecting without headphones.
A range of other audio options are available. Please
refer to the full instruction manual for further
information.
Battery
The X-TERRA uses 4 x AA batteries which are not included with the detector.
1. Access the battery compartment via the battery door located on the side of the control box. Slide the
battery compartment door upwards with your thumb.
2. Place individual batteries into the compartment as illustrated, ensuring the positive (+) and negative (–)
contacts match the diagram on the control box.
3. Close the battery door by pushing and sliding it downwards.