Mitsubishi Electric D700-SC User Manual

This guide is intended to complement the user manual provided by the manufacturer.
It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.
It should not be used as a replacement for the manual issued by the manufacturer.
Issue 1
20180129
This product is not a safety device. All safety considerations including but not
limited to Emergency Stop provision should be assessed separately and are
outside the scope of this guide.
Mitsubishi D700-SC Frequency Inverter
Easy Start Guide
The Mitsubishi D700-SC Frequency Inverter range is
available to order from inverterdrive.com

Mitsubishi Electric D700-SC Specifications

General

Series	D700
Type	DC Drive
Output Power	0.1 - 7.5 kW
Enclosure Rating	IP20
Output Voltage	0 - Input Voltage
Control Method	V/F control
Frequency Range	400 Hz
Protection Features	Overcurrent, Overvoltage, Overheat
Operating Temperature	-10 to 50°C
Storage Temperature	-20 to 65°C
Humidity	95% RH or less (non-condensing)
Altitude	Up to 1000m (3300 ft) above sea level
Input Voltage	200-240V AC, 380-480V AC

Summary

Power and Motor Connections (Single Phase)

Power and Motor Connections (Three Phase)

Motor Connections - Star and Delta

Motor connected in STAR (or Wye)

Explains connecting motors in Star configuration for dual voltage motors.

Motor connected in DELTA

Details Delta connection for dual voltage motors, often called "three-a-breast".

Parameters - overview

Parameters to set before use

Parameters to check and values to set

Lists essential parameters for basic D700 SC inverter operation and their recommended settings.

How to set a Parameter value

Select "PU” operation mode.

Guides on selecting the keypad operation mode for parameter changes.

Change mode to “Parameter setting”.

Instructs on accessing the parameter setting mode via the MODE key.

Select the required parameter.

Details how to navigate and select a specific parameter using the dial.

Change the parameter value and set.

Explains how to modify parameter values and save them using the SET key.

How to operate the Inverter from the keypad

Select "MON" and "PU" modes.

Sets the inverter to monitor mode and keypad control for operation.

Set the desired speed.

Guides on setting the target motor speed using the dial and confirming with SET.

Press the green “RUN” key to start the motor.

Instructions on starting the motor with the RUN key and adjusting speed during operation.

Press the red “Stop” key to stop the motor.

Explains how to stop the motor using the STOP key and its relation to parameter Pr. 8.

How to enable Sensorless Vector mode

Parameters to change to enable sensorless vector control

Lists parameters that need to be set for Sensorless Vector mode.

Enable monitoring and start auto tuning.

Details the process of initiating the auto-tuning run for Sensorless Vector mode.

Auto tuning is complete.

Describes the completion indicators and final steps after auto-tuning.

How to connect and configure a Potentiometer for remote speed control

Parameters to change for remote Potentiometer speed control

Lists parameters required to configure speed control using an external potentiometer.

Connecting the Potentiometer

Provides wiring instructions for connecting a potentiometer to the inverter for speed control.

How to connect and configure a Run Forward or Run Reverse switch

Parameters to change for remote Run/Stop

Details parameter settings for enabling remote Run/Stop control via a switch.

Connecting the Switch

Wiring guide for a 3-position switch for Run Forward/Stop/Reverse control.

How to connect and configure a Run/Stop switch with Forward/Reverse selection

Parameters to change for remote Run/Stop

Lists parameters to configure separate switches for Run/Stop and Forward/Reverse.

Connecting the Switch

Wiring instructions for two separate switches for Run/Stop and Forward/Reverse control.

How to configure "3-Wire" control with Run/Stop pushbuttons and Forward/Reverse selection

Parameters to change for remote 3-wire control

Parameters for setting up 3-wire control using pushbuttons and a selector switch.

Connecting the Switches

Wiring diagram for 3-wire control using pushbuttons and a switch.

Brake Resistor Connection (if available)

Parameters to change for Dynamic Braking

Parameters to enable dynamic braking for absorbing regenerative energy.

Connecting the Resistor

Instructions for wiring a brake resistor to the inverter terminals.

How to Reset the Inverter to Factory Defaults

Select "PU” operation mode.

Step to ensure the inverter is in keypad operation mode for resetting.

Change mode to "Parameter setting”.

How to access the parameter setting menu to find the reset parameter.

Select the “ALLC” parameter.

Identifies the specific parameter ("ALLC") used for factory reset.

Change the parameter value from 0 to 1 and set.

Process of changing the ALLC parameter value to execute the factory reset.