To Next PageTo Next PageWhat to do if Mitsubishi Electric FR-D720-0.4K shows heatsink overheat?
If the heatsink overheats, the temperature sensor is actuated and the inverter output is shut off. Set the surrounding air temperature to within the specified limits.
What to do if Mitsubishi Electric FR-D720-0.4K Inverter shows PU disconnection?
This function stops the inverter output if communication between the inverter and PU is suspended. Connect the parameter unit cable securely.
What causes regenerative overvoltage trip during constant speed on Mitsubishi Electric FR-D720-0.4K?
If regenerative energy causes the inverter's internal main circuit DC voltage to reach or exceed the specified value, the protective circuit is activated to stop the inverter output. Ensure that you keep load stable.
What does retry count excess mean on Mitsubishi Electric Inverter?
If operation cannot be resumed properly within the number of retries set, this function trips the inverter. Eliminate the cause of the error preceding this error indication.
What causes inrush current limit circuit fault in Mitsubishi Electric FR-D720-0.4K?
This function is activated when the resistor of the inrush current limit circuit overheats. Configure a circuit where frequent power ON/OFF is not repeated.
What to do if my Mitsubishi Electric FR-D720-0.4K Inverter is showing overcurrent trip during constant speed?
If your Mitsubishi Electric Inverter is showing an overcurrent trip during constant speed operation, make sure the load is stable. Also, check the wiring for any output short circuits or ground faults. Try lowering the stall prevention operation level and activating both the stall prevention operation and the fast-response current limit operation (Pr.156).
What does it mean when my Mitsubishi Electric Inverter shows an inverter overload trip?
An inverter overload trip on your Mitsubishi Electric Inverter means the electronic thermal relay function, which protects the inverter elements, has been activated. To resolve this, try increasing the acceleration/deceleration time, adjusting Pr. 0 Torque boost setting, setting Pr. 14 Load pattern selection appropriately, reducing the load, or ensuring the surrounding air temperature is within the specified limits.
How to solve Mitsubishi Electric FR-D720-0.4K Inverter stall prevention (overvoltage)?
During deceleration, stall prevention (overvoltage) happens if the regenerative energy of the motor becomes excessive. To prevent overvoltage trip, increase the deceleration time using Pr. 8 Deceleration time.
Why Mitsubishi Electric FR-D720-0.4K stall prevention (overcurrent) occurs?
Stall prevention (overcurrent) occurs during acceleration when the output current of the inverter exceeds the stall prevention operation level. This function stops the increase in frequency until the overload current decreases to prevent the inverter from resulting in overcurrent trip. Ensure that the Pr. 0 Torque boost setting is not too large.
What causes Mitsubishi Electric FR-D720-0.4K overload trip and how to fix it?
The inverter output stops if the temperature of the output transistor element exceeds the protection level when a current not less than the inverter rated current flows and overcurrent trip does not occur (200% or less). To resolve this, increase the acceleration/deceleration time.
General| Model | FR-D720-0.4K |
|---|---|
| Series | FR-D700 |
| Rated Output Capacity (kVA) | 0.8 |
| Output Rated Current (A) | 2.5 |
| Input Voltage | 200-240VAC |
| Input Phase | 3-phase |
| Horsepower | 0.5 HP |
| kW | 0.4 kW |
| Input Frequency | 50/60Hz |
| Cooling Method | Fan cooled |
| Humidity | 90% RH or less (non-condensing) |
| Output Voltage | 3-phase 200-240V AC |
| Output Frequency | 0.2 to 400 Hz |
| Control Method | V/F control, vector control |
| Frequency Range | 0.2 to 400 Hz |
| Protection Features | Overcurrent, Overvoltage, Short Circuit |
| Operating Temperature | -10°C to +50°C |
| Storage Temperature | -20°C to +65°C |
| Altitude | 1000m or less |
Verifies the inverter model and accessories against the order and ensures the product is intact.
Details the various peripheral devices that can be connected to the inverter for expanded functionality.
Provides instructions for safely removing and reinstalling the front and wiring covers for access.
Covers environmental requirements and design considerations for inverter installation enclosures.
Explains the terminal connection diagrams for main and control circuits, including options.
Details the specifications for main circuit terminals, including power input and motor wiring.
Defines specifications for control circuit terminals, including input, output, and communication signals.
Guides the connection of optional units like brake resistors, brake units, and reactors.
Addresses measures to reduce electromagnetic noise and handle leakage currents to prevent malfunctions.
Explains the necessity and procedure for installing reactors to prevent issues caused by power input circuits.
Recommends using magnetic contactors on the inverter's input side for safety and maintenance purposes.
Details measures for driving 400V class motors to prevent insulation deterioration due to surge voltages.
Provides essential guidelines to prevent product damage or shortened lifespan from incorrect handling.
Explains system configurations and interlocks to prevent accidents even if the inverter fails.
Describes the names and functions of the operation panel components for controlling the inverter.
Lists all available parameters, their settings, initial values, and related pages for reference.
Details how to adjust torque boost and other parameters to optimize motor performance.
Explains how to set maximum/minimum frequencies and avoid mechanical resonance points.
Describes setting base frequency, voltage, and load patterns for optimal V/F characteristics.
Covers multi-speed operation, jog operation, and remote setting functions using external terminals.
Details how to set acceleration, deceleration times, and patterns for smooth motor control.
Covers motor overheat protection and selection of appropriate motors for optimal performance.
Explains DC injection braking, regenerative braking, and various stop selection methods.
Details how to assign functions to input and output terminals for various control signals.
Describes how to select and display various operating status and monitor signals.
Covers automatic restart and power-failure deceleration stop functions for system continuity.
Explains retry functions and phase loss protection for managing fault conditions.
Details optimum excitation control to improve motor efficiency and achieve energy savings.
Provides techniques for reducing motor noise, EMI, and avoiding mechanical resonance.
Explains how to use analog signals for frequency setting, including bias and gain adjustment.
Covers functions like PU stop, parameter write disable, and password protection.
Details how to select operation modes (PU, External, Network) and control sources.
Explains PU connector wiring, RS-485 communication, and Modbus-RTU specifications.
Covers advanced functions like PID control, dancer control, and regeneration avoidance.
Describes functions such as cooling fan control, part life display, and maintenance timer alarm.
Details operations for setting parameters, changing display language, and adjusting panel contrast.
Explains how to connect and configure the FR-E500 series operation panel.
Provides instructions for clearing parameters to their initial values or clearing all parameters.
Allows viewing and setting parameters that have been changed from their initial values.
Explains how to check and clear the inverter's fault history records for diagnostics.
Describes the procedures for resetting protective functions after a fault occurs.
Provides a comprehensive list of fault and alarm codes displayed by the inverter.
Details common causes for error messages, warnings, and faults with their respective corrective actions.
Lists the mappings between digital codes and actual alphanumeric characters shown on the operation panel.
Offers initial checks and troubleshooting steps for common motor and machine issues.
Covers daily and periodic inspection procedures to prevent faults and ensure reliable operation.
Details how to measure main circuit electrical parameters using various instruments.
Presents the electrical ratings and specifications for different inverter models and power supplies.
Lists general specifications including control methods, frequency range, and input/output signals.
Provides detailed mechanical dimensions and panel cutouts for various inverter models.
