Mitsubishi Electric HC1500 User Manual (English)

Questions and Answers:

V
Vickie FoxAug 17, 2025
What to do if my Mitsubishi Electric Projector says 'No Signal'?
- J
  Jody GarciaAug 17, 2025
  If you see 'NO SIGNAL' displayed on your Mitsubishi Electric Projector, first ensure the connected device is powered on and functioning correctly. Check that the external device is outputting signals. Verify the cable connecting the projector to the external device is not defective and is connected to the correct terminals. Also, confirm that the connected device is correctly selected as the input source. If using an extension cord, try replacing it with the supplied cable to see if that resolves the issue; if it does, consider using an RGB signal amplifier with the extension cord.
M
michael21Aug 20, 2025
How to fix a Mitsubishi Electric Projector when no image appears?
- R
  Rhonda ValenzuelaAug 20, 2025
  If no image appears on the screen of your Mitsubishi Electric Projector, start by ensuring the lens cap is removed. It can take about a minute for the lamp to light up. If the lamp doesn't light, wait a few minutes and try again. If the projector was recently turned off before the lamp cooled, wait for the fan to stop before turning it back on. Also, check that the intake vent is clean, SCART INPUT in the FEATURE menu is set to OFF, and the lamp cover is closed. Ensure all cables connected to external devices are intact. If using an extension cable, test with the supplied cable; if it works, use an RGB signal amplifier with the extension cable. Finally, consult the video device's manual for proper connection guidance.
A
Anthony GarciaAug 23, 2025
Why does the Mitsubishi Electric HC1500 remote not work?
- I
  icastroAug 23, 2025
  If the remote control isn’t functioning properly with your Mitsubishi Electric Projector, check that the batteries are correctly loaded and not weak. Make sure the remote control sensor isn’t exposed to direct sunlight or fluorescent light. Ensure you are using the remote control within its operational range and at least 10 cm away from the projector.
S
Sheila ConradAug 25, 2025
Why does my Mitsubishi Electric HC1500 keep turning off?
- T
  Timothy LeeAug 26, 2025
  If your Mitsubishi Electric Projector turns off unexpectedly, it might be due to blocked intake and/or exhaust vents. Ensure these vents are clear. Also, check that AUTO POWER OFF is set to OFF. A deteriorating lamp may also cause the projector to turn off after a short period of illumination.
C
Cheryl Cherry DVMAug 28, 2025
Why are the projected images shaking on my Mitsubishi Electric HC1500?
- T
  Todd SmithAug 28, 2025
  If the projected images from your Mitsubishi Electric Projector are shaking or displaced, ensure the cable connected to the external device isn’t loose. Firmly connect the cable's plug to the external device's connector. You can also try pressing the AUTO POSITION button. If you are using some computers that output out-of-spec signals, adjust the SIGNAL menu.
J
Joseph SmithAug 30, 2025
What does 'TEMPERATURE!!' mean on my Mitsubishi Electric HC1500?
- E
  Edwin FrenchAug 30, 2025
  If your Mitsubishi Electric Projector displays 'TEMPERATURE!!', it indicates the ambient temperature is too high. Try to identify and eliminate the causes of the temperature increase. Also, check if the air inlet or outlet grille is blocked and remove any obstructions. If the filter is clogged, clean it.
S
Sarah LloydSep 1, 2025
How to brighten the image on a Mitsubishi Electric HC1500 Projector?
- C
  Carolyn LewisSep 2, 2025
  If the projected images from your Mitsubishi Electric Projector are dark, adjust the BRIGHTNESS and CONTRAST in the IMAGE menu. If the issue persists, consider replacing the lamp.
T
Taylor BoydSep 4, 2025
What to do if Mitsubishi Electric Projector buttons don't work?
- J
  Jennifer JordanSep 4, 2025
  If the buttons on the control panel of your Mitsubishi Electric Projector (except for the POWER button) don’t function, it's possible that PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS. Cancel the password lock or contact the person in charge of managing the projector.
C
Cristian BauerSep 6, 2025
How to fix blurred images on Mitsubishi Electric HC1500?
- N
  nielsenkelliSep 7, 2025
  If the projected images from your Mitsubishi Electric Projector are blurred, try adjusting the focus and cleaning the lens. You can also press the W or X button on the remote control to eliminate flicker. Adjust TRACKING and FINE SYNC in the SIGNAL menu, and BRIGHTNESS and CONTRAST in the IMAGE menu. Ensure the projector and screen are perpendicular to each other.
G
George BoydSep 9, 2025
Why does my Mitsubishi Electric HC1500 ask for a password?
- E
  erin91Sep 9, 2025
  If the screen for entering the password appears on your Mitsubishi Electric Projector, it means PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT. Enter the password or contact the person in charge of management of the projector.

Mitsubishi Electric HC1500 Specifications

General

Brightness	1600 ANSI lumens
Contrast Ratio	2500:1
Lamp Life	2000 hours
Weight	3.3 kg (7.3 lbs)
Dimensions	320 x 94 x 252 mm (12.6 x 3.7 x 9.9 inches)
Display Technology	DLP
Lamp Life (Low)	3000 hours
Lens Shift	No
Lamp Life (Eco mode)	3000 hours
Resolution	1280 x 720
Native Resolution	1280x720 (720p)
Zoom Ratio	1.2x
Input Ports	HDMI, Composite, S-Video
Projection Size	40 - 300 inch