Mitsubishi Electric MELSEC-Q QD75M - Page 849

Index - 4
Input signal logic selection (
Pr.22
) ........... 5-32
Interface internal circuit................................. 3-21
Intentional stop.............................................. 6-70
Internal circuit ................................................ 3-21
Internal current consumption .......................... 3-3
Interpolation axis ........................................... 9-21
Interpolation control....................................... 9-21
Interpolation speed designation method (
Pr.20
)
....................................................................... 5-32
Interruption request during continuous operation
(
Cd.18
)...................................................... 5-148
[J]
JOG operation ............................................... 11-4
JOG operation acceleration time selection
(
Pr.32
)........................................................ 5-36
JOG operation deceleration time selection
(
Pr.33
)........................................................ 5-36
JOG operation setting program .................... 6-41
JOG operation start time chart.................... 11-11
JOG operation timing and processing times
....................................................................... 11-6
JOG speed (
Cd.17
).................................. 5-148
JOG speed limit value (
Pr.31
) .................. 5-36
JOG start signal............................................. 3-14
JUMP instruction ......................................... 9-112
[K]
[L]
Last executed positioning data No. (
Md.46
)
..................................................................... 5-132
LED display functions................................ 15-106
LEND ........................................................... 9-115
List of block start data ................................... 5-98
List of condition data ................................... 5-104
List of configuration devices............................ 2-4
List of control data....................................... 5-138
List of dedicated instructions......................... 14-2
List of devices used......................................... 6-5
List of errors................................................... 15-6
List of functions................................................ 3-4
List of input signal details.............................. 3-20
List of input/output signals ............................ 3-14
List of monitor data...................................... 5-110
List of parameters.......................................... 5-22
List of positioning data .................................. 5-82
List of warnings............................................15-90
Load inertia (
Pr.112
) ....................................5-64
LOOP ...........................................................9-114
Lower limit......................................................3-21
[M]
M code (Condition data No., No. of LOOP to
LEND repetitions) (
Da.10
)..........................5-94
M code OFF request....................................12-65
M code OFF request (
Cd.7
).....................5-140
M code ON signal ..........................................3-15
M code ON signal output timing..................12-64
M code ON signal output timing (
Pr.18
) ...5-30
M code output function ................................12-64
Machine feed value........................................9-16
Machine feed value (
Md.21
).....................5-120
Machine OPR...................................................8-4
Machine response suppression filter (
Pr.118
)
........................................................................5-66
Machine response suppression filter 2 (
Pr.161
)
........................................................................5-80
Main functions..................................................3-6
Major positioning controls................................9-2
Manual control ...............................................11-2
Manual pulse generator...................................2-4
Manual pulse generator................................ A-14
Manual pulse generator cable..........Appendix-36
Manual pulse generator 1 pulse input
magnification (
Cd.20
) ...............................5-150
Manual pulse generator enable flag (
Cd.21
)
......................................................................5-150
Manual pulse generator input selection (
Pr.24
)
........................................................................5-32
Manual pulse generator operation ..............11-27
Manual pulse generator operation program
........................................................................6-42
Manual pulse generator operation start time chart
......................................................................11-34
Manual pulse generator operation timing and
processing times..........................................11-29
Mechanism of positioning control....................1-7
Monitor data area.............................................7-3
Movement amount after near-point dog ON
(
Md.34
)......................................................5-128
Monitor output 1 offset (
Pr.127
) ..................5-74
Monitor output 2 offset (
Pr.128
) ..................5-74
Motor capacity (
Pr.104
) ..............................5-60