To Next PageTo Next PageHow to fix Mitsubishi Electric Air Conditioner not cooling well?
If your Mitsubishi Electric Air Conditioner isn't cooling well, try these steps: First, clean the filter, as airflow is reduced when it's dirty. Next, check the temperature setting and adjust it as needed. Also, ensure there's enough space around the outdoor unit and that nothing is blocking the indoor unit's air intake or outlet. Finally, check if any doors or windows are open.
What to do if the Mitsubishi Electric PKA-A12HA6 trouble is not reoccurring and not logged?
If a problem with your Mitsubishi Electric Heat Pump occurred but is not reoccurring and not logged, re-check the abnormal symptom. Conduct troubleshooting to ascertain the cause of the trouble. If the cause is not ascertained, continue to operate the unit for the time being. If the problem persists, it may indicate no abnormality concerning parts such as electrical components, the controller board, or the remote controller.
What to do if the Mitsubishi Electric PKA-A12HA6 trouble is not reoccurring but logged?
If the trouble with your Mitsubishi Electric Heat Pump is not reoccurring but has been logged, it may be due to temporary defects such as the activation of protection devices in the refrigerant circuit (including the compressor), poor wiring connections, or noise. Re-check the symptom, and check the installation environment, refrigerant amount, weather when the trouble occurred, and wiring. After finishing service, reset check code logs and restart the unit. If the problem persists, it may indicate no abnormality in electrical components, the controller board, or the remote controller.
How to fix Mitsubishi Electric Heat Pump error code E3 or E5?
If your Mitsubishi Electric Heat Pump displays check code E3 or E5, it means there's a remote controller transmission error. This can happen if the remote controller couldn't find a blank transmission path for 6 seconds or if the remote controller receives and compares transmitted data, judging them as different 30 consecutive times. Set one remote controller to main and the other to sub. If the problem continues, diagnose the remote controller.
What does E0 or E4 mean on my Mitsubishi Electric PKA-A12HA6 Heat Pump remote?
If your Mitsubishi Electric Heat Pump displays check code E0 or E4, this indicates a remote controller transmission or signal receiving error. This can occur if the main or sub remote controller cannot receive any transmission normally from the indoor unit of refrigerant address “0” for 3 minutes, or if all remote controllers are set as “sub” remote controllers. First, check if the cause of the trouble is not in the mentioned causes. If the issue persists and there is no problem with the previous action, set one of the remote controllers to “main”.
Why does the display not appear on my Mitsubishi Electric PKA-A12HA6?
If the display messages on your Mitsubishi Electric Heat Pump do not appear when the operation switch is turned on, and the operation lamp does not light up, it might be due to incorrect wiring between the indoor and outdoor units (incorrect polarity of S1, S2, S3) or a short in the remote controller wire. Check the wiring of the remote controller.
What to do if my Mitsubishi Electric Heat Pump shows error code E6?
If your Mitsubishi Electric Heat Pump displays check code E6, it indicates an indoor/outdoor unit communication error, potentially due to contact failure, a short circuit, or incorrect wiring of the connecting wire between the indoor and outdoor units. Check the LED display on the outdoor control circuit board, using a Connect A-control service tool (PAC-SK52ST).
What to do if Mitsubishi Electric Air Conditioner shows error code?
If an error code appears on your Mitsubishi Electric remote controller display, the protection devices have operated to protect the air conditioner. Do not attempt to repair this equipment by yourself. Turn off the power switch immediately and consult your dealer. Be sure to provide the dealer with the model name and information that appeared in the remote controller display.
Why does my Mitsubishi Electric Air Conditioner stop before reaching set temperature?
If your Mitsubishi Electric Air Conditioner stops before reaching the set temperature during heating mode, it may be due to frost forming on the outdoor unit when the outdoor temperature is low and the humidity is high. The outdoor unit will perform a defrosting operation, and normal operation should begin after approximately 10 minutes.
Why is my Mitsubishi Electric Air Conditioner not blowing warm air immediately?
If warm air does not blow immediately from your Mitsubishi Electric Air Conditioner when heating operation starts, it is normal. Warm air will start blowing once the indoor unit has sufficiently warmed up.
General| Model | PKA-A12HA6 |
|---|---|
| Refrigerant | R410A |
| Indoor Unit Dimensions (HxWxD) | 12-1/2 x 39-3/8 x 9-7/8 inches |
| Outdoor Unit Dimensions (HxWxD) | 550 x 800 x 285 mm |
| Weight (Indoor Unit) | 9 kg |
| Power Supply | 220-240 V, 50 Hz |
| Type | Heat Pump |
| Coefficient of Performance (COP) | 3.61 |
| Coefficient of Performance (Heating) | 3.61 |
| Noise Level (Outdoor Unit) | 50 dB(A) |
