Mitsubishi Electric PUMY-P140VHMB User Manual (English)

Other manuals for Mitsubishi Electric PUMY-P140VHMB

Installation Manual136 pages

Installation Instructions136 pages

Installation Guide13 pages

Questions and Answers:

S
Sandra TorresAug 15, 2025
What to do if discharge/compressor temperature thermistor (TH4) exceeds limits in Mitsubishi Electric Air Conditioner?
- M
  Matthew PattersonAug 15, 2025
  If the discharge/compressor temperature thermistor (TH4) exceeds 125 or 110 continuously for 5 minutes in your Mitsubishi Electric Air Conditioner, it indicates a problem. This could be due to an over-heated compressor caused by a shortage of refrigerant, defective operation of the stop valve, a defective thermistor, a defective outdoor controller board, or a defective linear expansion valve. To address this, check the intake super heat, look for refrigerant leakage and add more refrigerant if needed. Make sure the stop valve is fully open. Turn the power off, then on again, and check if error code 5101 is displayed. If it is, refer to the 'Check points' for 5101. Also, check the linear expansion valve.
J
Jennifer HernandezAug 20, 2025
What to do if 63L operates under -0.03MPa during compressor operation in Mitsubishi Electric PUMY-P140VHMB Air Conditioner?
- G
  Gregory HowardAug 20, 2025
  If 63L operates below -0.03MPa during compressor operation of your Mitsubishi Electric Air Conditioner, it could be due to several reasons. The stop valve of the outdoor unit might be closed, there could be a disconnection or loose connection of connector (63L) on the outdoor controller board or of 63L itself, a defective outdoor controller board, refrigerant leakage or shortage, or a malfunction of the linear expansion valve. To fix this, check the stop valve and the connector (63L) on the outdoor controller board. Correct the refrigerant amount to the proper level and inspect the linear expansion valve.
M
marissa73Aug 23, 2025
What to do if detecting mode conditions are satisfied during compressor operation in Mitsubishi Electric PUMY-P140VHMB?
- H
  housefrankAug 23, 2025
  If your Mitsubishi Electric Air Conditioner is in HEAT mode and meets specific conditions, including a discharge super heat of 80 or more, a temperature difference (TH7-TH3) less than 5, and a high-pressure sensor reading below 2.04MPa, it may indicate a problem. This could be due to gas leakage or shortage, especially during heating operation, or a ball valve performance failure. To resolve this, check the refrigerant amount and the operation condition. Also, verify that the ball valve is fully opened.
S
Samantha WadeAug 27, 2025
How to troubleshoot malfunction of drain pump in Mitsubishi Electric PUMY-P140VHMB Air Conditioner?
- A
  andre75Aug 27, 2025
  A malfunctioning drain pump in your Mitsubishi Electric Air Conditioner could be caused by several factors: a defective drain, a clogged drain pump or pipe, water drops on the drain sensor (possibly from lead wire trickling or a clogged filter causing drain wave), or a defective indoor controller board. To troubleshoot, first, check if the drain pump is working. Then, inspect the drain function. Check the lead wire setting of the drain sensor and inspect the filter for clogs. If none of these issues are present, consider replacing the indoor controller board.
S
Susan MartinezAug 31, 2025
What to do if drain sensor detects water and temperature difference in Mitsubishi Electric PUMY-P140VHMB Air Conditioner?
- C
  Christopher MooreAug 31, 2025
  If the drain sensor in your Mitsubishi Electric Air Conditioner detects being soaked in water 10 times in a row, and the liquid pipe temperature minus room temperature is -10deg[-18°F] for 30 minutes, it indicates a malfunction of the drain pump. Check if the drain pump is working and inspect the drain function.
J
johnsonpatrickSep 4, 2025
Why outdoor fan motor rotational frequency is abnormal in Mitsubishi Electric PUMY-P140VHMB Air Conditioner?
- S
  Sarah HallSep 4, 2025
  If the rotational frequency of the fan motor is abnormal during operation in your Mitsubishi Electric Air Conditioner, it suggests an issue with the outdoor fan motor. This could be due to failure in the operation of the DC fan motor or failure in the outdoor circuit controller board. To address this, check or replace the DC fan motor. Also, check the voltage of the outdoor circuit controller board during operation and replace the board if necessary.
A
Amy WareSep 7, 2025
What to do if float switch detects water and turns on and off abnormally in Mitsubishi Electric PUMY-P140VHMB?
- D
  Daniel BallardSep 7, 2025
  If the float switch in your Mitsubishi Electric Air Conditioner detects water and turns on and off abnormally, it indicates a defective moving part of the float switch. Check the moving part of the float switch.

Mitsubishi Electric PUMY-P140VHMB Specifications

General

Cooling Capacity	14.0 kW
Heating Capacity	16.0 kW
Refrigerant	R410A
Operating Temperature (Heating)	-15°C to 24°C
Series	City Multi
Operating Temperature (Cooling)	-5°C to 46°C