To Next PageTo Next PageWhy does my Mitsubishi Electric TRANE CITY MULTI TPLFYP-FM140 make the room smell bad?
The Mitsubishi Electric Air Conditioner indoor unit draws in air that contains gases produced from the walls, carpeting, and furniture as well as odors trapped in clothing, and then blows this air back into the room.
Why is my Mitsubishi Electric Air Conditioner remote not working?
If nothing appears on your Mitsubishi Electric Air Conditioner wireless remote controller display, the display is faint, or signals are not received by the indoor unit unless the remote controller is close, the batteries are likely low. Replace the batteries and press the Reset button. If nothing appears even after the batteries are replaced, make sure that the batteries are installed in the correct directions (+, –).
Why won't my Mitsubishi Electric TRANE CITY MULTI TPLFYP-FM140 turn back on immediately?
If your Mitsubishi Electric Air Conditioner doesn't restart immediately after being stopped, wait approximately three minutes. The unit has stopped to protect itself.
Why does my Mitsubishi Electric Air Conditioner turn off by itself?
If your Mitsubishi Electric Air Conditioner stops without the ON/OFF button being pressed: * Check if the off timer is set and press the ON/OFF button to restart operation if it is. * If the air conditioner is connected to a central remote controller, consult the concerned people who control the air conditioner. * If “ ” appears in the remote controller display, consult the concerned people who control the air conditioner.
Why does my Mitsubishi Electric TRANE CITY MULTI TPLFYP-FM140 Air Conditioner stop before reaching the set temperature?
During heat mode, if your Mitsubishi Electric Air Conditioner stops before reaching the set room temperature, frost may have formed on the outdoor unit due to low outdoor temperature and high humidity. If this occurs, the outdoor unit performs a defrosting operation. Normal operation should begin after approximately 10 minutes.
What to do if Mitsubishi Electric Air Conditioner doesn't turn on?
If the Mitsubishi Electric Air Conditioner does not operate even though the ON/OFF button is pressed and the operation mode display on the remote controller disappears, check if the power switch of the indoor unit is turned off and turn it on.
What does “ ” mean on my Mitsubishi Electric Air Conditioner remote?
During central control, “ ” appears in the Mitsubishi Electric Air Conditioner remote controller display and air conditioner operation cannot be started or stopped using the remote controller.
Why doesn't my Mitsubishi Electric TRANE CITY MULTI TPLFYP-FM140 blow warm air right away?
Warm air does not blow from the Mitsubishi Electric Air Conditioner indoor unit until the unit has sufficiently warmed up.
What does it mean when the operation lamp is flashing on my Mitsubishi Electric Air Conditioner?
If the operation lamp near the receiver for the wireless remote controller on the Mitsubishi Electric Air Conditioner indoor unit is flashing, the self diagnosis function has operated to protect the air conditioner. Turn off the power switch immediately and consult your dealer. Be sure to provide the dealer with the model name. Do not attempt to repair this equipment by yourself.
Why is my Mitsubishi Electric TRANE CITY MULTI TPLFYP-FM140 leaking water outside?
Water or vapor may be emitted from the Mitsubishi Electric Air Conditioner outdoor unit: during cool mode, water may form and drip from the cool pipes and joints; during heat mode, water may form and drip from the heat exchanger; and during defrosting mode, water on the heat exchanger evaporates and water vapor may be emitted.
General| Brand | Mitsubishi Electric |
|---|---|
| Model | TRANE CITY MULTI TPLFYP-FM140 Series |
| Category | Air Conditioner |
| Language | English |
Explains safety symbols and critical warnings for safe operation.
Procedures for starting and stopping the air conditioner.
How to choose operation modes and set desired temperatures.
Using i-See sensor for room occupancy energy saving.
Automatic unit shutdown when no occupancy is detected.
How to operate the unit during remote controller failure.
Resolving problems with heating, cooling, and airflow.
Troubleshooting unit not operating, display errors, timer issues.
Interpreting error codes and "PLEASE WAIT" messages.
Technical specs and temperature operating ranges for models.
