To Next PageTo Next PageWhat to do if my Mitsubishi MJ-E16S-S1 Dehumidifier unit does not operate?
If your Mitsubishi Dehumidifier unit isn't operating, try these steps: Restore AC power supply, replace the fuse, perform a mechanical check, correct any defects, replace the switch if it's defective, or replace the control board.
Why won’t my Mitsubishi Dehumidifier dehumidify?
If your Mitsubishi Dehumidifier isn't dehumidifying, it could be due to a clogged filter. Clean the filter to resolve this. Another cause might be a low-temperature, low-humidity operating environment. Also you can repair the coolant circuit.
How to fix noise increase in Mitsubishi MJ-E16S-S1?
If you notice a noise increase in your Mitsubishi Dehumidifier, it could be due to pipe/pipe contact, in this case replace cooler or condenser; or replace discharge pipe welding. It may also be due to pipe/cabinet contact, so repair pipe molding.
General| Brand | Mitsubishi |
|---|---|
| Model | MJ-E16S-S1 |
| Category | Dehumidifier |
| Language | English |
Details the controls and indicators for the MJ-E16S model.
Details the controls and indicators for the MJ-E16SX model.
Explains the functions and displays shown on the unit's LCD panel.
Covers Easy Dehumidifying, Low, Low Temp, and Auto modes.
Covers LAUNDRY, Air Purifier, Easy Laundry, and Mildew Guard modes.
Covers High Humidity, Tank Full, Cold, and Defrosting indicators.
Explains louvre swing and timer settings.
Instructions for setting the ON timer for the E16SX model.
Instructions for setting the OFF timer for the E16SX model.
Highlights the 16-liter/day dehumidifying capacity and its benefits.
Highlights the 16-liter/day dehumidifying capacity and its benefits.
Explains the benefits of the wide-angle louvre for various applications.
Covers working temp, defrosting, wait time, heating, and room size.
Explains how the unit works and humidity readings.
Graph showing dehumidifying capacity vs. temp/humidity.
How LOW TEMPERATURE mode performs in low temp/high humidity.
Precautions, cleaning main unit, water tank, and air filter.
Replacing air filter and removing water from tank.
Electrical wiring schematic for the E16S model.
Electrical wiring schematic for the E16SX model.
Lists safety components like fuses and protectors.
Overall functional block diagram for E16SX.
Table detailing functions for the E16S model.
Table detailing functions for the E16SX model.
How compressor/blower switches by humidity/temp.
Common operational specs for all modes on E16SX.
Operation details for various modes across models.
Specific control logic for Mildew Guard mode.
Modifies settings based on room temp, humidity, circulation.
Timing sequence for E16S Easy Dehumidifying and Low Temp modes.
Timing sequence for E16S Auto mode.
Timing chart for the defrost cycle.
Timing chart for the off timer.
Timing for starting, mode switching, and stopping.
Timing related to humidity and temperature readings.
Timing for defrost and tank full detection.
Timing for swing mode changes and display.
Timing sequence for ON and OFF timer operations.
Schematic of the power supply board.
Schematic of the control board for E16S.
Schematic of the control board for E16SX.
Overall functional block diagram for E16S.
Step-by-step guide for diagnosing unit non-operation.
Simple checks for compressor, fan, and unit not running.
Procedures for tub temp and room temp/humidity sensors.
Procedures for compressor, fan motor, and solenoid valve resistance.
Lists error codes and corrective actions for E16S.
Lists error codes and corrective actions for E16SX.
Procedure for testing LCD and LED indicators.
Procedure to disable the compressor's 3-minute restart prevention.
Explains the monitor display modes for E16SX.
Procedure to run the demonstration mode for E16SX.
Procedure for testing LED sensor indications on E16S.
Steps to remove the water tank and front panel assembly.
Steps to remove the front case assembly and power supply board.
Steps to detach the main and power supply boards.
Steps to remove the rear case assembly.
Steps to remove the blower fan assembly and motor.
Procedure to remove the float switch.
Steps to remove the drain pan assembly and heat exchanger.
Instructions for attaching a hose for continuous drainage.
Guidelines for correct hose setup to prevent issues.
Exploded diagram of casing and structural parts.
List of casing and structural parts with part numbers.
Exploded diagram of electrical parts.
List of electrical parts with part numbers.
Exploded diagram of compressor related parts.
Detailed list of compressor parts with part numbers.
Common causes for the unit not operating.
Troubleshooting for dehumidifying not functioning or low levels.
Solutions for no airflow, noisy operation, and air smell.
Addressing problems with humidity not reaching set levels or louvre movement.
Covers noise reverberations, buzz, compressor issues, smell.
Explains tank deposits, marks, and humidity display variations.
Lists specific error codes and their meanings for troubleshooting.
Explains graphic symbols for warnings and cautions.
Warnings regarding power cords, plugs, and sockets.
Don'ts for disassembly, repair, and touching moving parts.
Precautions against water exposure and fire risks.
Precautions for installation, moving, and draining.
Precautions for dry environments and child supervision.
