Monacor TXA-802SR - Manual Channel Selection; Specifications; Setting the Squelch

9
English
3) To exit the group setting mode and to go to the
squelch setting mode (
☞
chapter6.1.3), press
the button SET. To exit the squelch setting mode,
press the button SET.
Note: The setting modes will be automatically exited after
5 seconds if no button is pressed. Any settings you may
have made will be saved.
Perform the channel scan for the first receiver, switch
on the appropriate two transmitters and set them
accordingly. Leave the two transmitters switched on
so that the channels already used will be skipped
during the channel scan for the second receiver.
Then perform the channel scan for the second re-
ceiver, switch on the two appropriate transmitters
and set them accordingly.
6.1.2 Manual channel selection
If both receiver units A and B are switched on:
1) Keep the button SET pressed until the channel
indication for receiver unit A starts flashing on
the display.
2) Use the button  or  to select the channel
for receiver unit A, then press the button SET
to confirm.
3) The channel indication for receiver unit B starts
flashing on the display. Use the button  or  to
select the channel for receiver unit B, then press
the button SET to confirm.
If only one receiver unit A or B is switched on:
Keep the button SET pressed until the channel in-
dication starts flashing on the display. Select the
channel with the button  or  and then confirm
with the button SET.
If a channel is not confirmed within 10 seconds with
the button SET, the setting mode will be exited and
the channel previously set will be kept.
Note: The receiver units A and B cannot be set to the
same channel.
6.1.3 Setting the squelch
The squelch function will mute the respective re-
ceiver unit when the level of the radio signal falls
below the threshold value adjusted. Thus, interfer-
ence signals will not cause noise when the trans-
mitter is switched off or when its radio signal is
insufficient: If the levels of the interference signals
are below the threshold value, the receiver unit will
be muted.
A high threshold value offers high interference
resistance, but it will also reduce the transmission
range. Thus, when the reception is good, a high
threshold value can be used; however, when the
transmitter and the receiver are far apart, a low
threshold value is recommended.
1) Switch off the receiver units A and B. Then keep
the button SET pressed, while switching on a re-
ceiver unit. The display will indicate the group
setting ( or , with the digit flashing).
2) To exit the group setting mode and to go to the
squelch setting mode, press the button SET: The
display will indicate (for “Squelch”) and the
current value (flashing).
3) Use the button  or  to set the value (level7=
highest threshold value).
4) To exit the squelch setting mode, press the but-
ton SET.
Note: The setting modes will be automatically exited after
5 seconds if no button is pressed. Any settings you may
have made will be saved.
7 Specifications
Radio frequencies
Channel Frequency Channel Frequency
01 863.1 MHz 09 863.2 MHz
02 864.1 MHz 10 864.2 MHz
03 863.6 MHz 11 863.7 MHz
04 864.6 MHz 12 864.7 MHz
05 863.3 MHz 13 863.4 MHz
06 864.3 MHz 14 864.4 MHz
07 863.8 MHz 15 863.9 MHz
08 864.8 MHz 16 864.9 MHz
Output level
XLR (bal.): . . . . . . . . . . . . . 30 mV
6.3 mm jack (unbal.): . . . . 730 mV (HIGH)
80 mV (LOW)
Power supply: . . . . . . . . . . . via PSU supplied
and connected to
230 V / 50 Hz
Dimensions (W × H × D): . . 215 × 44 × 210 mm
(w / o antennas and
feet)
Weight: . . . . . . . . . . . . . . . 1.2 kg
Subject to technical modification.
All rights reserved by MONACOR
®
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.