Monogram ZIS420D - Page 8

3/4” OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may
EHLQVWDOOHGRQWULPPHGPRGHOV7KHRYHUOD\SDQHOPXVW
EHVHFXUHGWRDµWKLFNEDFNHUSDQHOZKLFKVOLGHV
LQWRWKHWULP$VSDFHUSDQHOµWKLFNPXVWEHSODFHG
between the overlay and backer panel.
Assemble the panels with glue and screws:
&HQWHUWKHVSDFHUSDQHORQWKHEDFNHUSDQHOOHIWWR
right and top to bottom. Secure the panels with glue.
&HQWHUWKHVSDFHUDQGEDFNHUSDQHORQWKHRYHUOD\
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is
not always equal to top-to-
bottom offset.
8
Spacer Panel
Overlay Panel
Backer Panel
Fresh
Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispen-ser
Cutout
9-5/8"
Dispenser Cutout
15-3/8
"
&XWWKHGLVSHQVHURSHQLQJDIWHUWKHEDFNHUVSDFHUDQGRYHUOD\
panels have been assembled.
µ6LGHE\6LGHLQLQFKHV
  $ % & ' ( ) *
µ%DFNHU3DQHO       
µ6SDFHU3DQHO       
µ2YHUOD\3DQHO       
µ6LGHE\6LGHLQLQFKHV
  $ % & ' ( ) *
µ%DFNHU3DQHO       
µ6SDFHU3DQHO       
µ2YHUOD\3DQHO       
µ6LGHE\6LGHLQLQFKHV
  $ % & ' ( ) *
µ%DFNHU3DQHO      
µ6SDFHU3DQHO      
µ2YHUOD\3DQHO       
*Dispenser
&XWRXW3RVLWLRQ
IMPORTANT NOTE: Maximum total weight for the assembled
SDQHOV
)UHVKIRRGGRRUSDQHO²OEV
)UHH]HUGRRUSDQHO²OEV
Grille Panel – 18 lbs.
IMPORTANT NOTE – DISPENSER MODELS
7KHUHIULJHUDWRULVVXSSOLHGZLWKWZRGLVSHQVHUWULPV
RQHIRUIUDPHGSDQHOVDQGRQHIRURYHUOD\SDQHOV7KH
overlay dispenser trim is designed to fit a total panel
WKLFNQHVVRIµ
,IWKHSDQHOLVOHVVWKDQµDQRWLFHDEOHJDSPD\
be created around the dispenser trim.
,IWKHSDQHOLVPRUHWKDQµWKHGLVSHQVHUWULP
cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
.250” + .10” + .750” = 1.100” Total Panel Thickness
7KHRYHUOD\SDQHOPXVWEHFRQVWUXFWHGDFFRUGLQJWR
the specifications shown to achieve the correct total
thickness.
$OWHUQDWLYHSDQHOFRQVWUXFWLRQPHWKRGVVXFKDV
VHFXULQJDµSDQHOWRDµEDFNHUSDQHOFDQQRW
EHXVHG$QRWKHUPHWKRGURXWLQJDµWKLFNSDQHO
RQDOOVLGHVFDQQRWEHXVHG7KHVHPHWKRGVZLOOQRW
UHVXOWLQWKHUHTXLUHGµSDQHOWKLFNQHVV
When a raised panel design is to be used, a custom
middle rail is required. See page 9 for details.
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
Design Guide