To Next PageTo Next PageWhy won't my Montigo Indoor Fireplace pilot igniter spark?
If the pilot igniter won't spark, here are a few things to check: 1. Make sure the MAIN ON-OFF switch (typically located below the valve cover) is turned ON. 2. Ensure the main power is ON or that new batteries are installed in the remote control and backup battery pack (if available). 3. Check the 3.15A fuse in the control box and replace it if necessary.
What to do if the pilot igniter is sparking, but the pilot burner will not light on my Montigo DelRay DRL4813NI Indoor Fireplace?
If the pilot igniter is sparking, but the pilot burner won't light, you can try the following: 1. Verify the Inlet and Manifold Gas Pressure are within acceptable limits. 2. Check all connections to the gas valve. 3. Check the connection to the stepper motor (if available).
How to fix a Montigo DelRay DRL4813NI Indoor Fireplace when the pilot light is on, but the main burner will not light?
If the pilot light is on, but the main burner won't light, try these steps: 1. Check and verify all wiring connections according to the wiring diagram. 2. Verify that the inlet and Manifold Pressure are within acceptable limits.
What to do if pilot lights, but main burner will not light and igniter continues to spark in my Montigo Indoor Fireplace?
If the pilot light is on, but the main burner won't light and the igniter continues to spark, try the following: * Clean the Pilot Flame Sensor Rod with steel wool. * Clean the Pilot hood with steel wool if it's dirty. * Adjust the pilot flame using the pilot adjustment screw to ensure it fully engulfs the sensor rod and is stable. * Ensure the ground wire from the pilot is connected to the fireplace body.
What to do if pilot lights, but main burner will not light in my Montigo Indoor Fireplace?
If the pilot light is on, but the main burner of your Montigo Indoor Fireplace won't light, check and verify all wiring connections according to the wiring diagram and verify that the inlet and manifold pressure are within acceptable limits.
What to do if Montigo Indoor Fireplace pilot igniter is sparking, but pilot burner will not light?
If the pilot igniter is sparking, but the pilot burner won't light on your Montigo Indoor Fireplace, verify the Inlet and Manifold Gas Pressure are within acceptable limits. Also, check all connections to the gas valve and the connection to the stepper motor (if available).
Physical dimensions and specifications for DelRay 36 and 48 models.
Physical dimensions and specifications for DelRay 60 and 72 models.
Framing requirements and dimensions for 36" and 48" models.
Framing requirements and dimensions for 60" and 72" models.
Venting layout and termination requirements for DRL36 and DRL48 models.
Venting layout and termination requirements for DRL60 models.
Venting layout and termination requirements for DRL72 models.
Detailed instructions for installing a roof vent termination.
Component part numbers for 4/7 venting systems.
Component part numbers for 5/8 venting systems.
Wiring diagram for DRL models with SIT Proflame ignition.
Wiring diagram for DRL models with SIT Proflame ignition and fan control.
Step-by-step instructions for connecting the gas line.
Steps to initialize the remote control system for first-time use.
Initial operational steps after system initialization.
Instructions for turning the fireplace on using the remote.
Instructions for turning the fireplace off using the remote.
How to control flame height using the remote control.
Using the remote as a room thermostat for temperature control.
Using the smart thermostat function for automatic flame adjustment.
How to adjust the speed of the circulating fans via remote.
How to control the dimmable accent lighting via remote.
Procedures for cleaning the fireplace components, including glass.
General| Type | Indoor Fireplace |
|---|---|
| Model | DelRay DRL4813NI |
| Fuel Type | Natural Gas |
| Ignition Type | Electronic Ignition |
| Heat Output | 30, 000 BTU |
| Vent Type | Direct Vent |
| Glass Type | Tempered Glass |
| Weight | 150 lbs |
| Finish | Black |
| Dimensions | 48" W x 13" H |
