What to do if Motorola Two-Way Radio is dead and display doesn't turn on?
If your Motorola Two-Way Radio is dead and the display does not turn on, the cause might be a dead battery. Replace it with a charged battery.
Why does my Motorola Two-Way Radio have no receive audio or receiver does not unmute?
If your Motorola Two-Way Radio has no receive audio or the receiver does not unmute, the issue may be related to programming. Ensure the transmitted signal matches the receiver configuration (PL, DPL, etc.). Also, check if the radio can be unmuted with the monitor function enabled.
How to fix distorted or not loud enough audio on Motorola Two-Way Radio?
If the audio on your Motorola Two-Way Radio is distorted or not loud enough, it could be due to the synthesizer not being on frequency. Check the synthesizer frequency by measuring the transmitter frequency and realign if it is off by more than ±150 Hz (VHF) or ±500 Hz (UHF).
Why is the RF sensitivity poor on my Motorola Two-Way Radio?
Poor RF sensitivity on your Motorola Two-Way Radio may be caused by several factors: * The synthesizer may not be on frequency. Check the synthesizer frequency by measuring the transmitter frequency; realign it if it is off by more than ±150 Hz (VHF) or ±500 Hz (UHF). * Another possible cause is receiver front end tuning. Check RF front-end tuning for optimum sensitivity using the tuner.
What to do if Motorola Two-Way Radio has no RF power out?
If your Motorola Two-Way Radio has no RF power output, check the Tx power level and frequency programming using the tuner.
How to resolve no modulation or distortion modulation on Motorola Two-Way Radio?
If you are experiencing no modulation or distortion modulation on your Motorola Two-Way Radio, check the deviation and compensation settings using the tuner.
How to fix bad microphone sensitivity on Motorola Two-Way Radio?
If you are experiencing bad microphone sensitivity on your Motorola Two-Way Radio, check deviation and compensation and realign if necessary.
What causes no or low signaling (PL, DPL, MDC) on Motorola Two-Way Radio?
If you are experiencing no or low signaling (PL, DPL, MDC) on your Motorola Two-Way Radio, check the programming.
What does EPRM ERR mean on Motorola Two-Way Radio and how to fix it?
An EPRM ERR on your Motorola Two-Way Radio indicates a codeplug structure mismatch, non-existence of codeplug, or an EEGROM Checksum Error where the codeplug checksum is wrong. Reprogram the codeplug with the correct codeplug and retest. If the message reoccurs, replace the main board or send the radio to a depot.
What does SYN UNLK mean on Motorola Two-Way Radio and how to resolve it?
A SYN UNLK error on your Motorola Two-Way Radio means that the synthesizer is unlocked. Verify the codeplug and reprogram if necessary. If the message reoccurs, replace the main board or send the radio to a depot.
General| IP Rating | IP54 |
|---|---|
| Frequency Range | VHF: 136-174 MHz, UHF: 403-470 MHz |
| Channel Capacity | 16 |
| Signaling | DTMF, MDC1200 |
| Durability | MIL-STD 810 C/D/E/F/G |
| Operating Temperature | -30°C to +60°C |
Details the Push-to-talk (PTT), On-Off/Volume Knob, Channel Selector, LED Indicator, Microphone, and programmable side buttons.
Explains LED status indications for Radio Call, Scan, Call Alert, Selective Call, and Low Battery Level.
Describes using programmable buttons via short/long press or hold down for various radio functions.
Covers charging new or low-charge batteries, initial charging times, and desktop charger LED status.
Instructions for sending calls via PTT and responding to incoming calls, including volume adjustment.
How to initiate or terminate a scan operation using the Scan button or Auto Scan channels.
To Next Page