Motus M770E - User Manual

Questions and Answers

M
Michelle OlsonSep 3, 2025
What causes excessive resistance loading during the MANUAL program on the Motus Elliptical Trainer?
- J
  James SinghSep 3, 2025
  Excessive resistance during the MANUAL program on your Motus Elliptical Trainer may be due to a defective MPU board or a defective Drive board; test with a substitute board and replace if necessary. A worn or damaged wire harness can also cause this issue; inspect the wire harness and replace if necessary.
N
nicholasdavisSep 1, 2025
What to do if the Dot-LED and Numeric LED do not light up on the Motus M770E Elliptical Trainer (M770EL)?
- Y
  yhamiltonSep 1, 2025
  If the LCD TV is normal, but the Dot-LED and Numeric LED do not light up on your Motus Elliptical Trainer (M770EL), it could be due to a defective SMPS-5V (MPU Power Supply). If there is no voltage, replace the SMPS-5V. Also, check the wire harness. If there is no voltage, verify that the CBB3 cable interconnected with the CBB4 cable is plugged into both the MPU Board and SMPS-5V. Replace if necessary. Finally, the MPU Board itself may be defective; if there is no voltage, replace the MPU PCB.
K
kristinawarrenAug 31, 2025
Why is the Motus M770E LCD screen dark or black?
- Z
  Zachary TerryAug 31, 2025
  If the LCD screen on your Motus Elliptical Trainer is dark or black, the TV mode may not be set up. Press the Volume down button until “TV” is displayed on the left upper corner of the LCD screen. The display order is: “ANALOG”=>”VIDEO”=>”S-VIDEO”=>”TV”. As soon as “TV” is displayed, snow and noise will scatter on the LCD screen, or a picture will be captured.
M
Mary PageAug 29, 2025
What to do if the Motus M770E has no power to the console (M770EL)?
- A
  andrewmannAug 29, 2025
  If there is no power to the console of your Motus Elliptical Trainer (M770EL), first check the main circuit breaker and wall outlet voltage at the facility. If voltage is present, replace the line cord. If the line voltage is ok, then the power-on switch may be damaged. Replace the power-on switch if the output voltage of the power switch is not present.
A
Amanda StanleyAug 27, 2025
What to do if contact heart rate reading is erratic on Motus M770E?
- R
  Rachel BrownAug 28, 2025
  If the contact heart rate reading on your Motus Elliptical Trainer is erratic or not displayed, consider the following: * The CHR PCB may be faulty and need replacement. * The handlebar sensors might be dirty; wipe them with a clean, soft cloth. * There may be a defective cable or bad connection between the CHR PCB and MPU PCB; check the cable and connection. * The user may have an unusual heart rate condition; have a different user grasp the sensors to detect any variances.
C
Catherine PowersAug 26, 2025
What to do if the Motus M770E Elliptical Trainer displays 'snow and noise' on the LCD screen?
- A
  Amanda EllisAug 27, 2025
  If your Motus Elliptical Trainer LCD screen displays snow and noise, and no picture appears when using the channel buttons, the air/cable setting may be incorrect; follow the setup procedures in the LCD manual. Ensure the TV signal source is correctly supplied to the A/D PCB from an external source, and that the cable is secure. If the external TV signal is correct, connect the coaxial cable directly to the internal connector in the AD PCB of the Console to check the internal cables. The 75 ohm coaxial cable may also be bad and require replacement. If the issue persists, the A/D Board may be damaged and need replacing.
W
washingtoncraigAug 25, 2025
How to fix erratic heart rate reading using wireless chest strap on Motus M770E?
- M
  meganmillerAug 25, 2025
  An erratic or missing heart rate reading when using a wireless chest strap on your Motus Elliptical Trainer can occur for several reasons: * Ensure the chest strap electrodes are sufficiently damp with tap water. * Maintain a distance of more than 30 cm between cardio equipment. * Make sure the chest strap is within 60cm of the Wireless HR PCB. * Replace the chest strap or its battery. * Ensure the chest strap electrodes lie flat and horizontally across your skin. * If problems persist, the chest strap or Wireless HR PCB may be faulty and require replacement. Also, check the cable and connection between the Wireless HR PCB and MPU PCB.
B
bjohnsonAug 23, 2025
What to do if the Motus M770E Elliptical Trainer console LEDs are not illuminating?
- D
  David WiseAug 23, 2025
  If the console LEDs on your Motus Elliptical Trainer are not illuminating, it could be due to a faulty MPU board or Drive board. Use a multi-meter to verify more than 6VDC at pin-7 and pin-8 on CN1. If voltage is present, replace the MPU board. If not, replace the Drive board. Also, check that the main cable CN1 is securely plugged into both the MPU board and Drive board, replacing it if necessary. Finally, inspect the wire harness for any wear or damage and replace if needed.