To Next PageTo Next PageHow to unlock Movincool Office Pro 10 control board?
If your Movincool Air Conditioner isn't responding to the control board or buttons and no diagnostic code is shown, the unit may be in programming mode and locked out. To resolve this, press the RUN and SET buttons simultaneously.
Why is my Movincool Air Conditioner not cooling enough?
Insufficient cooling in your Movincool Air Conditioner can stem from several factors. First, ensure that the environmental conditions are within the design specifications by adjusting installation or operation conditions. Check and clean or replace the air filter if it's clogged, and also clean the fins if they are clogged. Adjust the set point temperature if it exceeds the room temperature. Other potential causes include a defective room temperature thermistor (replace it), an improperly ducted exhaust outlet (duct it properly), a leak in the refrigerant system (repair it), or a restriction in the refrigerant system (identify and remove it).
What to do if my Movincool Office Pro 10 is leaking water?
If your Movincool Air Conditioner is leaking water, several issues could be the cause. It could be that the condensate pump isn't working, in which case you should repair or replace it. Ensure the drain tank is installed. If the drain tank is cracked, replace it. Check for any obstructions in the drain pan hole and clear them. Finally, make sure the drain hose isn't kinked; if it is, un-kink it.
How to fix a Movincool Office Pro 10 that won't turn on?
If your Movincool Air Conditioner isn't operating, start by checking for power at the receptacle and terminal block. If the fan mode DIP switch is set to “Stop” and the current set point temperature exceeds the room temperature, check all wire connections. Also, if the fan mode DIP switch is set to “Stop” and the unit has a defective condensate pump, check the relay board fuse. Other potential issues include a defective drain tank switch (check the relay board fuse), a defective or incorrect relay board (check all wire connections), or a defective control board (check all wire connections).
Why does my Movincool Office Pro 10 have weak airflow?
If you're experiencing insufficient airflow from your Movincool Air Conditioner, start by cleaning the filters, as clogged fins on the evaporator or condenser (due to running the unit without filters) can restrict airflow. Also, check the fan setting and adjust it if it's on “Low”. A defective fan motor could also be the culprit, requiring replacement. Lastly, ensure that the static pressure doesn't exceed design specifications and adjust it if necessary.
Why is my Movincool Office Pro 10 Air Conditioner making noise and shaking?
Abnormal noise or shaking in your Movincool Air Conditioner can be attributed to several factors. Check the compressor mounting nut and tighten it if it's loose. Inspect the rubber grommet on the compressor mounting bolt for deformation or wear and replace it if necessary. Internal interference with other components may also cause these issues, so adjust internal components to eliminate interference. Finally, a damaged or out-of-balance fan can lead to noise and shaking, requiring repair or replacement.
What to do if Movincool Office Pro 10 starts then stops?
If your Movincool Air Conditioner starts but stops immediately, the room temperature and antifreeze thermistor connectors might be reversed on the control board; correct the wiring connection. Alternatively, a defective fan motor or compressor motor could be the cause, requiring replacement. A defective relay board could also be the issue, and you should replace it.
General| Cooling Capacity | 10, 000 BTU/h |
|---|---|
| Power Supply | 115V/60Hz |
| Refrigerant | R-410A |
| Exhaust Hose Diameter | 5 inches |
| Operating Temperature Range | 64°F to 95°F |
| Power Consumption (Cooling) | 1100 W |
| Noise Level (High) | 52 dBA |
| Hose Length | 5 ft |
Defines WARNING, CAUTION, and NOTE terms used in the manual.
Provides precautions for selecting a suitable location for the unit.
Instructions on how to safely move the unit using side handles and casters.
Guides on checking and connecting the power cord to the outlet.
Details the function of each button and indicator on the unit's control panel.
Explains how to use the unit in COOL mode and turn it off.
Explains how to use the unit in Fan Only mode and turn it off.
Instructions on switching from Fan Only mode to COOL mode.
Steps to set the current time and day for programming functions.
Guides on selecting a program and setting the start day and time.
Details on setting the stop time, temperature, and fan speed for programs.
Instructions for changing fan speed and cycling between Cool/Fan modes in programs.
Explains program cycling options and how to cancel a running program.
Explains how the thermistor controls automatic mode switching.
Explains the DIP switch function for fan operation after compressor cycles off.
Explains the DIP switch for changing temperature display (°C vs °F).
Instructions for emptying the condensate drain tank and related warnings.
Guides on attaching the condenser plenum and reducer components.
Lists the components included in the window kit accessory.
Instructions for attaching reducers to the window spacer and installing it.
Details on connecting ductwork to the reducer and unit, with warnings.
Explains the buttons and display functions of the optional remote control.
Explains the function and operation of the optional drain pump kit.
Instructions on how to clean the air filters for optimal performance.
Describes the method for cleaning the air filter elements.
Outlines inspection and maintenance tasks for in-season and off-season periods.
Lists error codes displayed on the control board and their meanings.
