Why is my mspa Hot Tub not heating properly?
Your MSpa Hot Tub might not be heating properly due to several reasons: the temperature might be set too low (set a higher temperature), the heating element may have failed (contact the MSpa Service Center), or the water level might be below the minimum line (add more water).
Why is the water in my mspa M-051LS Super Camaro not clean?
If the water in your MSpa Hot Tub isn't clean, it could be due to insufficient filtering time (increase filtration time), a dirty filter cartridge (clean or replace the filter cartridge in time), or improper water maintenance (refer to the chemical manufacture’s instruction).
What to do if the bubble air blower does not work on my mspa M-051LS Super Camaro?
If the bubble air blower on your MSpa Hot Tub isn't working, it might be because the pump is too hot (unplug the control box, and reset in a while), the bubble motor is short circuit (contact the MSpa Service Center), or auto-off 10 minute (waiting for 10 minutes and turn on the Bubble button again).
Why is the filter pump not working on my mspa Hot Tub?
If the filter pump on your MSpa Hot Tub isn't working, it could be due to a power failure (check the power source), the filter is stuck by dirt or other objects (contact the MSpa Service Center), or the water level is not at the minimum water line (add more water to the minimum line).
What to do if my mspa Hot Tub has no display on the control panel?
If there is no display on the control panel of your MSpa Hot Tub, the possible causes are: a power failure (check power source), the PRCD is off (reset PRCD), the PRCD is broken or pin plug connection failure (contact the MSpa Service Center).
What to do if my mspa Hot Tub is leaking?
If your MSpa Hot Tub is leaking, it could be due to a few reasons: the spa inlet/outlet connection might not be securely tight (tighten the inlet and outlet connection), the drainage valve is not closed completely (contact the MSpa Service Center, if spa is still leaking), or there's a leak in the spa pool body (repair the leaking hole/spilt with the repair kit material).
Why is my mspa M-051LS Super Camaro Hot Tub losing air pressure?
Your MSpa Hot Tub could be losing air pressure because the air valve got loosen (fill up the tub with air, make sure the air valves are secure, replace if necessary) or there is a hole or split on the spa tub (put soap water in a squirt bottle and spray on seams. If there is a leak it will bubble. After you find the leak, clean and dry the leaking area, then use the repair patch comes with your spa).
Why is my mspa M-051LS Super Camaro in an abnormal shape?
If your MSpa Hot Tub is in an abnormal shape, it could be due to extra air pressure caused by strong sunshine. Please check the air pressure and release air if necessary. During hot weather, it's recommended to check if it is necessary to release some air to avoid any possible damage to the spa pool.
Measures to prevent accidental drowning, child access, and ensuring cover security.
Precautions for electrical connections, appliances near the spa, and wet environments.
Guidelines for selecting a suitable installation site and ensuring proper support and drainage.
Step-by-step instructions for testing the PRCD before each spa use to ensure safety.
Detailed steps for inflating the spa tub using the air valve, hose, and manometer.
Instructions for filling the spa tub with water to the correct level and checking air pressure.
Explanation of the ON/OFF, Bubble, Filter, Heater, and UP/DOWN buttons.
Lists error codes (E0-E3), their causes, and recommended solutions.
Solutions for issues like no display, PRCD problems, and spa water leaks.
Addresses problems with heating not working and the bubble air blower not functioning.
General| Model | M-051LS |
|---|---|
| Type | Inflatable Hot Tub |
| Heater | 1500W |
| Temperature Range | 20-40°C |
| Material | 6-layer Reinforced PVC |
| Control System | Digital Control Panel |
| Filter Pump | 12V |
| Capacity | 5 People |
| Heat Increasing Rate | 1.5°C per hour |
To Next Page