Need help?Do you have a question about the MTD 219-381-000 and is the answer not in the manual?
Remove tiller and loose parts from carton; check all items and literature before discarding.
Slide tailpiece into chassis and secure with U-clevis pin and hairpin clip.
Install inner tine assemblies correctly for proper soil entry and tilling width.
Lever controls engine speed and stops the engine; adjust for various modes.
Squeeze lever to engage forward tine drive; release to stop forward motion.
Squeeze lever to engage reverse tine drive; release to stop reverse motion.
Service engine with gasoline and oil as per separate engine manual.
Follow safety warnings and steps for choke, throttle, and starter rope.
Move throttle to STOP and disconnect spark plug wire for safety.
Adjust wheel yoke for desired tilling depth and forward speed.
Lock or swing tailpiece/depth stake for maneuverability or depth control.
Adjust wheel yoke, depth stake, and handle pressure for desired results.
Use for cultivating soil to a 2-3 inch depth; adjust for width.
Pivot depth stake forward to lock; move under own power at slow speed.
Refer to 'How To Use Your Tiller' for wheel yoke and position adjustment.
Refer to 'How To Use Your Tiller' for depth stake adjustment.
Refer to 'Cultivating' section for adjusting tine width.
Refer to final adjustment section of assembly instructions.
Minor adjustment may be needed for fuel, temp, altitude, or load.
Adjust throttle control cable for proper engine speed and stopping function.
Lubricate moving parts and pivot points at least once a season with SAE 30 engine oil.
Chain case pre-lubricated; requires grease if disassembled, order part number.
Instructions for removing and replacing the forward drive belt.
Instructions for removing and replacing the reverse drive belt.
Lists all parts for the Model 381 tiller with part numbers and descriptions.
Detailed parts list for the chain case assembly.
Information on obtaining parts and service from authorized dealers.
Details the manufacturer's warranty policy and claim requirements.
Remove tiller and loose parts from carton; check all items and literature before discarding.
Slide tailpiece into chassis and secure with U-clevis pin and hairpin clip.
Install inner tine assemblies correctly for proper soil entry and tilling width.
Lever controls engine speed and stops the engine; adjust for various modes.
Squeeze lever to engage forward tine drive; release to stop forward motion.
Squeeze lever to engage reverse tine drive; release to stop reverse motion.
Service engine with gasoline and oil as per separate engine manual.
Follow safety warnings and steps for choke, throttle, and starter rope.
Move throttle to STOP and disconnect spark plug wire for safety.
Adjust wheel yoke for desired tilling depth and forward speed.
Lock or swing tailpiece/depth stake for maneuverability or depth control.
Adjust wheel yoke, depth stake, and handle pressure for desired results.
Use for cultivating soil to a 2-3 inch depth; adjust for width.
Pivot depth stake forward to lock; move under own power at slow speed.
Refer to 'How To Use Your Tiller' for wheel yoke and position adjustment.
Refer to 'How To Use Your Tiller' for depth stake adjustment.
Refer to 'Cultivating' section for adjusting tine width.
Refer to final adjustment section of assembly instructions.
Minor adjustment may be needed for fuel, temp, altitude, or load.
Adjust throttle control cable for proper engine speed and stopping function.
Lubricate moving parts and pivot points at least once a season with SAE 30 engine oil.
Chain case pre-lubricated; requires grease if disassembled, order part number.
Instructions for removing and replacing the forward drive belt.
Instructions for removing and replacing the reverse drive belt.
Lists all parts for the Model 381 tiller with part numbers and descriptions.
Detailed parts list for the chain case assembly.
Information on obtaining parts and service from authorized dealers.
Details the manufacturer's warranty policy and claim requirements.
General| Engine Displacement | 208cc |
|---|---|
| Tine Count | 4 |
| Forward Rotations | Yes |
| Reverse Rotations | No |
| Tilling Width | 16 inches |
| Tine Direction | Forward rotating |
| Warranty | 2 years |
To Next Page
