MTD 600 Series Service Manual (English)

Other manuals for MTD 600 Series

Service Manual13 pages

Shop Manual150 pages

Illustrated Parts Manual68 pages

Operator's Manual44 pages

Questions and Answers:

E
Elizabeth JonesAug 23, 2025
Why MTD Snow Blower engine fails to start?
- B
  brownangelaAug 23, 2025
  Your MTD Snow Blower engine might fail to start due to several reasons: the choke may not be in the CHOKE position, the spark plug wire might be disconnected, the fuel tank could be empty or contain stale fuel, the engine may not be primed, the spark plug could be faulty, the safety key may not be fully inserted, or the extension cord may not be connected (if equipped with an electric start). To resolve this, move the choke to the CHOKE position, connect the wire to the spark plug, fill the tank with clean, fresh fuel, prime the engine as instructed in the Engine Manual, clean/adjust/replace the spark plug, insert the safety key fully, or connect the extension cord to a grounded AC outlet.
D
David GentryAug 25, 2025
How to fix MTD Snow Blower engine that fails to start?
- A
  Antonio HuffmanAug 25, 2025
  If your MTD Snow Blower engine won't start, several factors could be at play. First, ensure the choke is in the CHOKE position and the spark plug wire is securely connected. Next, check that the fuel tank isn't empty or filled with stale fuel; if so, replenish it with clean, fresh fuel. Make sure you've primed the engine as per the Engine Manual. Inspect the spark plug for faults, cleaning, adjusting the gap, or replacing it if necessary. Verify the safety key is fully inserted into the switch. Lastly, if your model has an electric start, confirm the extension cord is properly connected to both the snow blower and a grounded 120V AC outlet.
Z
Zachary MartinAug 25, 2025
What to do if MTD 600 Snow Blower engine fails to start?
- A
  Angela Ortega MDAug 26, 2025
  If your MTD Snow Blower engine won't start, here's what you can check: 1. Ensure the choke control is in the ON position. 2. Make sure the spark plug wire is securely connected. 3. Verify the fuel tank isn't empty and contains fresh gasoline. 4. Prime the engine as detailed in the Operation section of your manual. 5. Inspect the spark plug; clean, adjust the gap, or replace it if necessary. 6. Confirm the safety key is fully inserted into the switch.
C
Charles GarciaAug 26, 2025
How to start my MTD 600 if the engine fails to start?
- S
  sandraclarkAug 27, 2025
  If the engine of your MTD Snow Blower fails to start, consider these possible causes: * The choke might not be in the CHOKE position. If so, move the choke to the CHOKE position. * The spark plug wire could be disconnected. Ensure the wire is connected to the spark plug. * The fuel tank may be empty or contain stale fuel. Refill the tank with clean, fresh gasoline. * The engine might not be primed. Prime the engine as instructed in the Operation Section. * The spark plug could be faulty. Clean, adjust the gap, or replace it. * The key may not be fully inserted into the ignition. Insert the key fully into the switch.
C
Caleb StoneAug 27, 2025
Why overhead chute crank does not stay stationary while throwing snow using an overhead chute control in MTD 600 Snow Blower?
- R
  Richard ArcherAug 27, 2025
  If the overhead chute crank on your MTD Snow Blower does not stay stationary, there might be insufficient preload applied to the chute control. Refer to the Service section to adjust the chute preload.
G
Grace MartinAug 28, 2025
Why MTD 600 engine running erratically?
- K
  Katherine GarrisonAug 28, 2025
  An MTD Snow Blower engine running erratically could be due to: * The engine running on CHOKE. Move the choke lever to the RUN position. * Stale fuel. Replace with clean, fresh gasoline. * Water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel.
G
Gail VincentAug 29, 2025
Why MTD Snow Blower has loss of power?
- K
  Kimberly WallAug 29, 2025
  Loss of power in your MTD Snow Blower could be due to: * A loose spark plug wire. Connect and tighten the spark plug wire. * A plugged gas cap vent hole. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
M
Mary LeeAug 30, 2025
Why does my MTD 600 engine run erratically?
- S
  Shelly ThomasAug 30, 2025
  An MTD Snow Blower engine might run erratically due to several reasons: 1. Check if the engine is running on CHOKE; if so, move the choke control to the OFF position. 2. Stale fuel can cause issues; replace it with clean, fresh gasoline. 3. Water or dirt in the fuel system can also be a culprit; drain the fuel tank and refill with fresh fuel. 4. If the above steps don't resolve the issue, the carburetor might be out of adjustment. In this case, contact a Tecumseh Engine Service Center.
P
popeannAug 31, 2025
What to do if my MTD Snow Blower fails to discharge snow?
- C
  Christian PerezAug 31, 2025
  If your MTD Snow Blower fails to discharge snow, here are a few things to check: * The chute assembly might be clogged. Stop the engine immediately and disconnect the spark plug wire. Then, clean the chute assembly and the inside of the auger housing using a clean-out tool or a stick. * There could be a foreign object lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger using a clean-out tool or a stick. * The shear pins may be sheared. Replace them with new shear pins.
L
Lance ThomasSep 1, 2025
Why is my MTD 600 Snow Blower engine running erratically?
- L
  Latasha EverettSep 2, 2025
  If your MTD Snow Blower engine is running erratically, with inconsistent RPM, consider the following potential causes: * The engine might be running on CHOKE. Move the choke lever to the RUN position. * The fuel could be stale. Fill the tank with clean, fresh gasoline. * There may be water or dirt in the fuel system. Drain the fuel tank and refill it with fresh fuel.

MTD 600 Series Specifications

General

Auger Material	Steel
Skid Shoes	Adjustable
Type	Two-Stage
Clearing Width	26 inches
Stages	Two-Stage
Engine Displacement	208 cc
Intake Height	21 inches
Throw Distance	Up to 40 ft