Mytee 8070 - User Manual

Questions and Answers

E
Elizabeth Hatfield MDJul 27, 2025
What to do if the pump is not running properly on Mytee 8070?
- M
  morgan75Jul 27, 2025
  If the pump on your Mytee Floor Machine isn't running as it should, consider these potential causes and solutions: * **Quick disconnects:** Ensure quick disconnects are firmly snapped together. * **Solution tank:** Refill the solution tank with a premixed detergent. * **Clogged jet:** Clean the jet on the upholstery tool with a soft wire brush or flush it after removing. * **Clogged filters:** Remove and rinse the filters with water. * **Heater blockage:** Flush the heaters with system maintainers, or replace them if still blocked with hard water deposits. * **Stuck check valve:** Replace the brass check valve. * **Disconnected pump wire:** Reconnect the pump wire. * **Bad switch:** Replace the switch on the switch plate. * **Worn pump motor brushes:** Replace the pump.
Z
Zachary ChandlerAug 3, 2025
How to troubleshoot a Mytee 8070 Floor Machine heater that is not working properly?
- B
  Barbara ReyesAug 3, 2025
  If the heater on your Mytee Floor Machine isn't working right, try these steps: * **Popped back up sensor:** Reset the sensor by pushing in the button. * **Worn automatic sensor:** Replace the automatic sensor with a new one. * **Disconnected heater wire:** Reconnect the heater wire.
K
Kimberly HansenAug 10, 2025
How to fix Mytee 8070 that will not turn on?
- G
  georgesmithAug 10, 2025
  If your Mytee Floor Machine won't turn on, here's what you can check: * **Not plugged in:** Ensure the machine is plugged into a working outlet. * **Circuit breaker:** Reset the circuit breaker. Avoid running other appliances on the same 15-amp circuit. * **Disconnected wire:** Check if the power cord wire has detached from the terminal block and reattach it.
J
Jason SmithAug 18, 2025
Why is the vacuum motor not working properly on my Mytee 8070 Floor Machine?
- K
  Kenneth JonesAug 18, 2025
  If the vacuum motor on your Mytee Floor Machine isn't functioning correctly, check the following: * **Loose hose:** Ensure the hose is tightly connected to both the upholstery tool and the machine. * **Open drain valve:** Completely close the drain valve. * **Loose vacuum tank lid:** Secure the vacuum tank lid tightly. * **Ball float shut off:** Empty all wastewater from the vacuum tank. * **Water in vacuum motor:** Use a low foaming detergent. * **Clogged upholstery tool:** Clean the upholstery tool of hair, carpet fibers, and debris. * **Bad switch:** Replace the switch on the switch plate. * **Worn vacuum motor armature:** Replace the vacuum motor.

Summary

Safety Precautions

General Operating Precautions

Rules for safe operation, including operator training and environment.

Safe Usage Practices

Guidelines for using the machine, handling cords, and chemicals.

Servicing Safety

Procedures for safely unplugging and servicing the machine.

Electrical Safety

Emphasizes grounding, proper outlets, and avoiding damaged cords.

Flammable Material Warning

Warns against using flammable materials with the machine.

Warranty Information

Wear Parts Warranty

Covers replacement of wear parts for 90 days from purchase.

Component Warranties

Details 1-year warranty for pumps, motors, and heaters.

Housing Warranty

Outlines a pro-rated 5-year warranty for rotational-molded housings.

Warranty Limitations and Exclusions

Specifies limitations on damages and conditions that void the warranty.

Unpacking the Machine

Inspect for Shipping Damage

Instructions to check packages for damage before unpacking.

Included Components List

Lists the parts included with the Mytee Lite II unit.

Optional Accessories

Available Accessories List

Lists optional tools like rinse systems and wands for purchase.

Attaching the Handle

Handle Assembly Steps

Guides user through attaching the handle with bolts and washers.

Machine Setup

Component Identification

Identifies key parts of the machine for setup.

Safety Label Familiarization

Locates and explains the importance of safety labels on the unit.

Filling the Solution Tank

Instructions on filling the solution tank and handling warnings.

Connecting Hoses

Details on securely connecting the solution hose to the machine.

Connecting Vacuum Hose

Instructions for connecting the vacuum hose to the recovery tank.

Power Connection

Guides plugging the machine into a properly grounded outlet.

Operation Guide

Priming the Pump

Steps to turn on the pump and prime it before heating.

Heating and Vacuum Activation

Instructions for turning on the heater and vacuum power.

Cleaning Procedure

Guidance on starting the cleaning process and checking upholstery care tags.

Operational Tips

Cord Safety and Maintenance

Advices on avoiding cord damage and proper maintenance.

Foam Control and Cleaning Techniques

Tips on using foam control, cleaning soiled areas, and upholstery care.

Hose Management and Vacuum Efficiency

Guidance on connecting hoses, maintaining vacuum power, and relieving pressure.

Chemical Handling

Recommendations for pre-mixing powdered cleaning agents.

Draining the Recovery Tank

Pre-Draining Safety

Emphasizes unplugging the machine before draining.

Tank Draining Procedure

Step-by-step guide to safely remove and empty the recovery tank.

Maintenance Procedures

Daily Maintenance Tasks

Routine cleaning and inspection of the machine and power cord.

Weekly Maintenance Tasks

Flushing the solution system, inspecting hoses, and cleaning spray tips.

Storing the Machine

Instructions for properly draining and storing the machine indoors.

Troubleshooting Guide

Unit Will Not Turn On

Addresses issues with power connection, circuit breakers, and wiring.

Pump Not Running Properly

Diagnoses problems with quick disconnects, solution levels, and clogged parts.

Heater Not Working Properly

Covers issues with sensors, wiring, and heating elements.

Vacuum Motor Not Working Properly

Troubleshoots hose connections, tank lids, ball floats, and motor issues.

Replacement Parts

Component Part Numbers

Lists part numbers for key components like motors, pumps, and filters.

Mytee 8070 Specifications

General

Solution Tank Capacity	3 gallons
Recovery Tank Capacity	3 gallons
Pump	120 PSI
Vacuum Motor	3 Stage
Power Cord Length	25 ft
Vacuum Lift	130 inches

Related product manuals

Mytee 8070 Mytee-Lite