NAD USB AUDIO
In order to stream your computer audio via M51, ensure that the Sound or
Audio device setting of your computer is set to “NAD Audio 2.0 Output”.
A NAD USB Audio driver can be downloaded via the NAD website link
http://nadelectronics.com/products/masters-series/M51-Direct-
Digital-DAC. Download “NAD USB Audio driver” from the “Manuals/
Downloads” tab. Install this NAD USB Audio driver to your computer by
following the instructions provided.
MINIMUM PC SYSTEM REQUIREMENT
Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7
FOR MAC USERS
Minimum Mac OS X Snow Leopard (version 10.6) and later versions already
include “NAD USB Audio” driver. Update your Mac OS if you cannot locate
NAD USB Audio driver.
IMPORTANT NOTICE
The use of the NAD USB Audio driver downloaded through the NAD site
is done at the customer’s own discretion and risk. The customer will be
solely responsible for any damage to his/her computer system or loss of
data arising out of or in connection with the use of this software driver.
In no event shall NAD be liable for any direct, indirect, incidental, special,
exemplary, or consequential damages including negligence or otherwise
arising in any way out of the use of this software driver.
VOLUME SETUP
The M51 VOLUME control function is dependent upon the “Volume Setup”
menu setting. “Volume” can either be set to “Fixed” or “Variable”. Press
[SETUP] button to launch “Volume Setup” menu. From “Volume Setup”
menu, press [ENTER] or [S] to bring up “Fixed” or “Variable” settings.
Fixed
If “Volume” is set to “Fixed”, audio output level is xed and the M51’s
Volume Control is bypassed.
• Press [D/F] to set a desired preset dB level. Conrm setting by
pressing [ENTER] or [S]. Thereafter, audio output from M51 can be
adjusted by using the volume control of the separate amplier the
M51 is linked into.
• If “Volume Setup” is set to “Fixed”, remote control’s [VOL 5/6] will
have no eect and eectively disabled.
Variable
• When set to “Variable”, the Volume level is directly adjustable using
the remote control’s [VOL 5/6] button. Correspondingly, audio
output from M51 can be adjusted by using the volume control of
the separate amplier the M51 is linked into.
POLARITY
Allow compensation for recordings that have reversed polarity.
Positive: A positive sine wave at the input remains positive at the
output. Polarity is defaulted to “Positive” setting.
Reversed: A positive sine wave at the input is negative (inverted) or
reversed at the output.
RENAMING A SOURCE INPUT
A particular source input can be renamed according to your preference.
You can use up to 16 characters in renaming a source input. Below is
the procedure on how to rename a source input. Note that all buttons
mentioned below are with reference to the remote control.
Example: Rename “HDMI 1” to “BD PLAYER”.
1 Press [HDMI 1] button to go to HDMI 1 source. “HDMI 1” is shown in the
upper section of the VFD.
2 Then, press and hold [DISP] button until “HDMI 1” is shown in the upper
section of the VFD and with “H” ashing.
3 Within 5 seconds, toggle the [D/F] buttons to select the rst character
(“B” from the alphabetical list). The ranges of characters available are A-Z,
a-z, _ (space) and 0-9.
4 Press [S] or [ENTER] to select the character and at the same time move
on to the next character. Press [A] to return to the previous character.
Repeat steps 3 and 4 for each character in sequence.
5 Complete the renaming process by pressing the [DISP] button again to
save the new Source input name.
NOTES
The renaming process will be automatically terminated if no button
is pressed within 5 seconds. Any renamed characters at the time of
termination will be not saved.
USING THE M51
OTHER FEATURES
10
To Next Page
Loading...
