NAPCO GEMINI C Series - AREA SYSTEM TROUBLE REPORTING OPTIONS (AREAS 5-8)

NAPCO Security Group
NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2
Page 78 Programming Instructions, Volume 2
AREA SYSTEM TROUBLE REPORTING OPTIONS (A DDRESS 1930-1967)
SYSTEM RESPONSE
ACTIVATED BY AREA 8
EVENT/TROUBLE
AREA 8 SYSTEM EVENT/TROUBLE
ADDR
AMBUSH
KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX.*
KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE
RSRVD.
1 2 3 4 5 6 7 8
Pulsed Burg. Bell
1960
Burglary Bell
1961
Burg PGM2
1962
Burg Relay
1963
Burg PGM1
1964
Report Alarm Telco 1
1965
Report Alarm Telco 3
1967
[Default = blank (•) blank (•) from address 1960-1967] * NOTE: Keypad Aux. is not to be selected for UL Installations.
SYSTEM RESPONSE
ACTIVATED BY AREA 5
EVENT/TROUBLE
ADDR
AREA 5 SYSTEM EVENT/TROUBLE
AMBUSH
KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX.*
KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE
RSRVD.
1 2 3 4 5 6 7 8
Pulsed Burg. Bell
1930
Burglary Bell
1931
Burg PGM2
1932
Burg Relay
1933
Burg PGM1
1934
Report Alarm Telco 1
1935
Report Alarm Telco 3
1937
[Default = blank (•) blank (•) from address 1930-1937] * NOTE: Keypad Aux. is not to be selected for UL Installations.
SYSTEM RESPONSE
ACTIVATED BY AREA 6
EVENT/TROUBLE
ADDR
AREA 6 SYSTEM EVENT/TROUBLE
AMBUSH
KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX.*
KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE
RSRVD.
1 2 3 4 5 6 7 8
Pulsed Burg. Bell
1940
Burglary Bell
1941
Burg PGM2
1942
Burg Relay
1943
Burg PGM1
1944
Report Alarm Telco 1
1945
Report Alarm Telco 3
1947
[Default = blank (•) blank (•) from address 1940-1947] * NOTE: Keypad Aux. is not to be selected for UL Installations.
SYSTEM RESPONSE
ACTIVATED BY AREA 7
EVENT/TROUBLE
AREA 7 SYSTEM EVENT/TROUBLE
ADDR
AMBUSH
KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX.*
KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE
RSRVD.
1 2 3 4 5 6 7 8
Pulsed Burg. Bell
1950
Burglary Bell
1951
Burg PGM2
1952
Burg Relay
1953
Burg PGM1
1954
Report Alarm Telco 1
1955
Report Alarm Telco 3
1957
[Default = blank (•) blank (•) from address 1950-1957] * NOTE: Keypad Aux. is not to be selected for UL Installations.
 1. Select the desired option entering the option number (1-8) for each digit.
 2. Enter corresponding option number in address location.
NOTE: Dark shaded data value box shows option not available.
 3. Press U to save.