NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 2
Page 24 Installation Instructions, Volume 2
FIRE GLOSSARY
Security Code). The Dealer Keypad Program Code allows the same access to programming functions as the Master Security
Code.
Dealer Keypad Unlock
Program this feature (in the Quickloader System Assignment screen, System Reporting and Outputs tab) to allow the re-
porting to the central station when any Dealer Keypad Program Code is used to unlock a GEMC-FK1 Fire keypad.
Digital Dialer Test
Unlocking the GEMC-FK1 Fire keypad and activating the digital dialer test from the Function Menu (TEST COMMUNICA-
TOR) will send the programmed report code to the central station. Program DD TEST for SYSTEM-TROUBLE REPORTS
and enter a DD TEST Report Code. Note that in this case the report code received is not indicative of a system trouble, but is
an indication of a successful transmission. Should the transmission fail, the keypad will display:
SYStrbl E03 xxx
MM/DD/YY HH:MM
'TELCO COMM FAIL '
'E03-000 SERVICE
This "E03" system trouble will clear after any successful subsequent report.
Disable Audible at Keypad on Resound
Located in the Keypad Assignment screen, Keypad Features tab. Troubles will re-sound at the keypad and report to the
central station (if programmed) within at least every 24 hours (some wireless transmitter troubles require resound within 4
hours). Where acceptable by the AHJ, the local keypad Audible sounder can be disabled when the trouble is being reported
to the central station.
Disable Call Waiting (TouchTone
®
Dialing Only)
A digital communicator connected to a telephone line with Call Waiting may be disrupted by this feature. However, most lines
with Call Waiting also have Selective Call Waiting, which permits the feature to be turned off by dialing a "*70" just before the
telephone number. A "*" will be dialed by programming a "B".
If the installation has the Call Waiting feature, be sure that it also has Selective Call Waiting, and confirm the disable code
with the telephone company. Then program this code ("B70") directly before the phone numbers (after dial-tone detection or
pre-dial delay) in the telephone-number locations. See Telephone Numbers.
Caution: Should the user cancel his Call Waiting service, the communicator will dial a wrong number unless the phone num-
ber is corrected.
Disable Call Waiting on 1
st
Attempt
Cancel "*70" after the 1
st
dial attempt. Default is disabled. When enabled, this option will dial the Central Station telephone
number as it is programmed in the panel. If the first communication is unsuccessful, the next and remaining dial attempts will
remove the * star button (entered as a "B" from the keypad) and the 2 subsequent digits from the Central Station telephone
number.
Disable Callback Download See Callback-Method Download
Disable Fire Zone
Every Fire zone may be disabled at the Fire keypad. Unlock the GEMC-FK1 Fire keypad, select DISPLAY ZONE DIRECTORY
and scroll to the desired zone, and press the DISABLE button. Press RESET to exit the function Menu. The TROUBLE and
DISABLE icons will flash. To un-disable the Fire zone, repeat the process and press DISABLE again. An alternate method,
in the Function Menu, scroll to DISPLAY ZONES DISABLED and press ENTER, scroll using the NEXT button until the zone
appears, then press DISABLE to "un-disable".
Disable Keypad Function-Mode Download See Callback-Method Download
Double Reporting See Report Telco 3
Download Security Code
This code is not a keypad code, but is only used to permit local or remote connections to be established between PCD-
Windows Quickloader download software and the control panel. Used during the connection process, if the panel code does
not match the code in Quickloader, a data connection will be denied. Some dealers with multiple PCD-Windows Quickloader
accounts use the same Download Security Code for all accounts. When attempting to establish a connection, if this code is
forgotten, the Master Security Code of the particular control panel can be used in its place.
Enable Fire Trouble Resound see Fire Trouble Resound
To Next Page
Loading...
Need help?
General
