NAPCO StarLink SLE-LTEVI Series User Manual

StarLink
™
SLE Commercial LTEVI & LTEAI Series Dual-Path Alarm Communicators -- Installation Instructions 1
ADDITIONAL COMPONENTS
In addition to the models listed above, the following sub-
assemblies are available:
SLE-ULPS-R - Power Supply. Required for installations
where the control panel cannot provide the Auxiliary
power required to operate the StarLink radio. Uses a
standard 4AH / 12V minimum (7AH maximum, required
with optional Wi-Fi Module) rechargeable battery to pro-
vide radio standby power. Requires connection to either
the model NAPCO TRF12/T123 (16.5V / 20VA) external
plug-in transformer or the chassis-mounted 16.5VAC /
20VA transformer affixed inside the housing (see wiring
diagrams further in this manual). Note: For models
without the SLE-ULPS-R, connect the radio terminals 1
and 2 to the control panel Aux Power terminals
(observing polarity).
SLE-WIFI-MODULE - Allows your Napco StarLink
™
device
to connect to the Internet by means of a wireless (Wi-Fi)
link, eliminating a wired Ethernet cable connection.
Note: 7AH battery required when using the SLE-
WIFI-MODULE. For more information, see WI2191.
SLE-DLCBL - Download Cable, 6 feet
SLE-ANTEXT30 - Extended antenna with 30 feet of cable
SLE-ANTEXT50 - Extended antenna with 50 feet of cable
SLE-ANTEXT75 - Extended antenna with 75 feet of cable
SLE-ANTEXT100 - Extended antenna with 100 feet of cable
(Any suitable external cellular antenna is permitted by
UL). Always follow the manufacturer's installation in-
structions. Note: Antennas are not Listed by UL.
GEM-Tamperkit - Tamper switches and screws to protect
metal housing (see page 14).
SPECIFICATIONS
The following specifications apply to all StarLink radio mod-
els unless otherwise stated:
Electrical Ratings for 120VAC, 60Hz
For Models with Power Supply
 Input Voltage: 120VAC nominal
StarLink™ SLE Commercial
LTEVI & LTEAI Series
Dual-Path Alarm Communicators
INSTALLATION INSTRUCTIONS
WI2327ELF 11/19
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440 or visit us at
http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC
© NAPCO 2019
INTRODUCTION
The StarLink
™
LTE Series Dual-Path Commercial / Resi-
dential Fire alarm capture radio IP communicators are fully
supervised, wireless digital two-way subscriber units. All
models are compatible with most 12/24VDC alarm control
panels (always adhere to the documentation provided by
the control panel manufacturer). These communicators are
for use as the primary means of communication with the
central station and do not have backup mode capability.
No POTS (Telco Line) connection permitted. See WI2140
for programming information.
The following models are available:
SLE-LTEVI-CFBPS & SLE-LTEAI-CFBPS: Commercial /
Residential Fire LTE Radio-TCP/IP Communicators in
red metal housing with SLE-ULPS-R power supply and
16.5V / 20VA transformer mounted inside housing
SLE-LTEVI-CFB & SLE-LTEAI-CFB: Commercial / Resi-
dential Fire LTE Radio-TCP/IP Communicators in red
metal housing. Powered directly from control panel (no
power supply, no transformer, rated nominal 12/24VDC
input)
The following features are included with models that in-
clude a SLE-ULPS-R power supply:
 Power limited output to the StarLink radio PC board 12V
input terminals
 Battery connection red and black flying leads
 Monitored battery charging and Active battery test circuits
 StarLink radio trouble input (from StarLink radio PC
board PGM1 terminal to detect StarLink radio trouble)
 Requires a sealed lead acid min 4AH / max 7AH battery
for minimum 24-hour standby time (max charge current
200mA).
 Trouble relay output (C, N/O and N/C terminals) to
wire to a panel zone dedicated to "Radio Trouble" (dry
contacts). Remove jumper "J2" isolate relay OUT1
common from ground
 Green AC ON LED visible from the exterior housing
 Yellow TROUBLE LED "D4" on PC board. Flashes sig-
nify:
One flash: AC fail / brownout
Two flashes: Low battery
Three flashes: Charging circuit trouble
Four flashes: StarLink radio trouble
The housing-mounted transformer (when provided) is
mounted inside its own housing compartment with a re-
placeable UL Listed .5A fast blow primary fuse. 120VAC
connections are to be made by a licensed electrician using
suitable connectors, in accordance with N.E.C. and local
code requirements.
AGENCY LISTINGS
 UL 864 Standard For Control Units and Accessories For Fire
Alarm Systems, 10th Edition
 UL 1610 Standard For Central-Station Burglar-Alarm Units
 UL 985 Standard For Household Fire Warning System Units
 UL 1023 Standard For Household Burglar-Alarm System Units
 UL 1076 APOU Proprietary Alarm Systems
 UL 365 APAW Police Connect

NAPCO StarLink SLE-LTEVI Series Specifications

General

Brand	NAPCO
Model	StarLink SLE-LTEVI Series
Category	Cell Phone
Language	English

Summary

INTRODUCTION

Available Models

Lists Commercial/Residential LTEVI/LTEAI series models with or without power supply.

ADDITIONAL COMPONENTS

Lists optional accessories like power supply, Wi-Fi module, and antennas.

SPECIFICATIONS

Specifies electrical ratings for 120VAC and input voltage.

AGENCY LISTINGS

Lists relevant UL and other agency compliance standards.

TERMINAL DESCRIPTIONS

TB1-TB13 Terminal Functions

Details the function of each terminal from TB1 to TB13.

Primary/Secondary Telephone Ports

RJ-45 sockets for FACP DACT connection.

Ethernet Port

Connection for broadband modem, router, or switch.

TB19: N/O OUT1

Normally open dry contact for Form C relay output.

LED DESCRIPTIONS

Diagnostic LEDs

Describes Green RF Signal, Yellow Status, Red Trouble, Red Diagnostic, and Green IP LEDs.

NOTICE TO AUTHORITIES HAVING JURISDICTION...

Lists settings for remote downloading, unsupervised inputs, supervision, and Wi-Fi.

SUPPLYING POWER

JUMPER DESCRIPTIONS

Details jumper settings on the PC board.

PRIMARY REPORTING

How the StarLink radio functions as a primary wireless IP communicator.

INSTALLATION STEPS

STEP 1: ACCOUNT REGISTRATION

Process for creating an account and registering the StarLink radio.

STEP 2: SELECT A MOUNTING LOCATION

Guidance on selecting location, verifying signal strength, and safety.

STEP 3: WIRING (PRIMARY MODE)

Details wiring for primary mode communication, including TELCO ports.

STEP 4: APPLY POWER

Instructions for applying power to the unit.

STEP 5: SIGNAL VERIFICATION

Verify signals online via www.NapcoNOC.com.

NAPCO GEMINI C-SERIES (GEMC) CONTROL PANEL PROGRAMMING

Use PCD-Windows Quickloader for programming reporting formats.

Programming StarLink Radio Troubles

Trouble Activation Wiring Options

Wiring for trouble activation using EOLR in series or parallel.

Wiring for Models without SLE-ULPS-R

Wiring instructions for models without SLE-ULPS-R power supply.

STARLINK RADIO RELATED EVENT REPORT CODES

SIGNALS ORIGINATED AT THE NOC

StarLink Radio Supervision

Telco Wire Supervision and Detection

Supervision of Telco wires and detecting cuts.

Supervision Time Schedule Considerations

Configuration Download / Firmware Updates

Technician Requirements for Updates

Technician requirements for commercial and residential updates.

Cover Tamper

Tamper Switch Installation

Optional front and rear tamper switches for metal housings.

(Commercial Fire) SLE-LTEVI-CFBPS & SLE-LTEAI-CFBPS Wiring Diagram

Wiring Notes

Telco Trouble and Line Cut Wiring

Connect StarLink to panel for Telco Trouble and line cut detection.

120VAC Wiring Requirements

Licensed electrician required for 120VAC wiring.

OUT1 Configuration and Wiring

Configuration and wiring of OUT1 relay for trouble reporting.

Wiring Diagram for Generic FACPs with TELCO RJ Sockets

Optional Power Supply Connection

Connect FACP Aux Power or listed power supply to terminals 1 & 2.

Tip/Ring Wiring Fault Report Supervision

Tip/Ring Wiring Fault Report feature required for supervision.

JP2 Option for Telco 2 Monitoring

Instructions for using JP2 option with power supply wire.

Wiring Diagram for Generic FACPs without TELCO RJ Sockets

RJ31X vs Direct Panel Wiring

Optional wiring to RJ31X for longer distances or direct to panel.

JP2 Option for Telco 2 Monitoring

Instructions for using JP2 option with power supply wire.

Wiring Diagram for GEMC-32, GEMC-96, GEMC-128 and GEMC-255 Control Panels

IN2 Connection for Telco Line Cut

Connect IN2 to panel output for identifying Telco line cut.

JP2 for Telco 2 Trouble

Remove JP2 to enable TELCO2 trouble reporting.

JP1 Shunt for SLE-ULPS-R

Shunt JP1 on top 2 pins when using SLE-ULPS-R.

NOTES

Alternate Telco Line to Alarm Panel Supervision

Method for using existing FACP telco connections for supervision.

Tamper Switch Mounting Instructions

Tamper Switch Wiring

Instructions for wiring tamper switches.

Tamper Switch Mounting Locations

Locations for mounting tamper switches in the cabinet.

Tamper Loop Wiring to Control Panel

Wire tamper loop as a normally closed sensor to a control panel zone.

4/2 Pulse Dialing Format Compatibility

Optional Alternate Methods for Commercial Fire Branch Circuit Power Connections to the SLE Charger Board

Conduit Location Example

Example of conduit location for wiring.

UL Listed Pull Box Power Connection Method

UL listed method for branch circuit power connections.

Transformer Secondary Wiring Conduit Limit

Limit transformer secondary wiring conduit to 20 feet.

NAPCO LIMITED WARRANTY

IMPORTANT WIRING METHODS

Single-Conductor Terminal Block Wiring

Proper wiring methods for single-conductor terminal blocks.

Barrier Type Terminal Block Wiring

Proper wiring methods for barrier type terminal blocks.

Pigtail Wiring for Multiple Conductors

Pigtail wiring method for multiple or different sized conductors.