Need help?Do you have a question about the Navico 2kW and is the answer not in the manual?
General| Brand | Navico |
|---|---|
| Model | 2kW |
| Category | Marine Radar |
| Language | English |
Regulatory compliance statement regarding radio frequency interference.
Regulatory compliance statement for Canadian radio frequency interference.
Declaration of conformity with EU essential requirements and provisions.
Legal disclaimer regarding product improvements, user responsibility, and liability.
Information about the Navico warranty card and where to find queries.
Request for user feedback to improve manual quality.
Describes the components and function of the Navico radar system.
Safety warnings regarding radar usage and potential hazards.
Lists the components of the Navico radar system and how to check them.
Guidance on selecting an optimal location for the radar scanner.
Specific installation guidance for radar scanners on power boats.
Specific installation guidance for radar scanners on yachts.
Formula and method to calculate the maximum radar detection range.
Method for determining the best scanner height for performance.
Techniques to minimize false echoes and shadow zones in radar images.
Step-by-step instructions for mounting the radar scanner unit.
Guidance on installing a scanner using a trestle or radar mast.
Instructions for installing the radar processor unit in a suitable location.
Connecting the 2 kW scanner to the interconnection cable.
Connecting the 4 kW scanner to the interconnection cable.
Details on connecting the radar processor to various display heads.
Connecting the 2 kW interconnection cable to the radar processor.
Connecting the 4 kW interconnection cable to the radar processor.
Instructions for connecting the power cable to the radar processor.
Steps for connecting the radar processor chassis ground wire.
Final checks for the radar system wiring and installation.
Lists required parts for connecting radar to GB40/8000i systems.
Diagram and steps for connecting radar to GB40 with SimNet heading sensor.
Diagram and steps for connecting radar to NMEA 0183 heading sensor.
Instructions for starting up and configuring the radar with GB40/8000i.
Lists required parts for connecting radar to NX40/NX45/M84/M121.
Diagram and steps for connecting radar to NX40/NX45/M84/M121.
Instructions for setting up radar with NX40/NX45/M84/M121 systems.
Lists required parts for connecting radar to Northstar 6000i/6100i.
Diagram showing connection of radar processor to 6000i/6100i display.
Connecting the radar communications cable to the junction box.
Setting up remote power control for 6000i/6100i with a common power source.
Setting up remote power control for 6000i/6100i with different power sources.
Instructions for setting up radar with Northstar 6000i/6100i.
Procedures for turning the radar system on and off.
Setting up navigator communications for radar integration.
Adjusting visual settings like mode, gain, and clutter for optimal radar display.
Requirements for heading sensors used with the radar system.
Steps to disable heading sensor input if not installed.
Procedures for calibrating the newly installed radar system.
Steps to prepare the radar system for calibration.
Guidance on tuning the radar for optimal performance.
Setting the Sensitivity Time Control curve for proper echo display.
Adjusting trigger delay for accurate radar sweep.
Calibrating heading for radar image alignment with heading sensor.
Calibrating heading for radar image alignment without a heading sensor.
Restoring all radar settings to their original factory defaults.
Restoring display appearance settings to factory defaults.
Manual tuning steps for specific situations where auto-tuning is insufficient.
Lists required parts for connecting radar to Lowrance displays.
Detailed instructions for connecting the radar to Lowrance displays.
Steps for setting up radar display, including trigger delay, heading line, and tune adjustments.
Routine maintenance procedures for the radar system.
Specific maintenance procedures for the radar scanner unit.
Additional maintenance tasks, including heading calibration reset.
Information on obtaining technical support and warranty service.
Troubleshooting steps for common radar operational issues.
Troubleshooting steps if the radar scanner fails to rotate.
Methods to reduce or eliminate noise and interference affecting radar performance.
Checks for proper power supply and wiring to the radar processor.
Dimensional drawings of the 2 kW radar scanner.
Dimensional drawings of the 4 kW radar scanner.
Dimensional drawings of the radar processor unit.
Technical specifications for the 2 kW radar system.
Technical specifications for the 4 kW radar system.
To Next Page
