Need help?Do you have a question about the Navico 4kW and is the answer not in the manual?
General| Brand | Navico |
|---|---|
| Model | 4kW |
| Category | Marine Radar |
| Language | English |
Details FCC rules, industry Canada operation, and CE compliance for the radar system.
Outlines product usage responsibility, liability disclaimer, and warranty information.
Provides contact information for submitting comments and suggestions about the manual.
Explains the radar system components, including scanner, processor, and connection cables.
Highlights critical warnings related to radar usage, high voltage, and microwave radiation hazards.
Lists the components included with the Navico radar system and verification steps.
Provides guidelines on choosing the optimal location for the radar scanner on a vessel.
Details specific considerations for installing the scanner horizontally or tilted on power boats.
Covers yacht installation, gimbal mounting, and calculating theoretical maximum detection range.
Explains how to find the optimum scanner height and reduce false echoes/shadow zones.
Provides instructions for installing the scanner unit and mounting it on a trestle.
Guides on selecting a dry location and installing the radar processor unit.
Details the procedure for connecting the interconnection cable to the 2 kW scanner.
Details the procedure for connecting the interconnection cable to the 4 kW scanner.
Identifies interface connectors on the radar processor for various display heads.
Explains how to connect the interconnection cable to the radar processor for 2 kW and 4 kW.
Guides on connecting the power cable and ground wire to the radar processor.
Provides a checklist for visually verifying the radar system wiring and connections.
Lists scanner, radar processor, and Ethernet cables needed for GB40/8000i integration.
Details connecting the Navico radar to a GB40 using SimNet heading sensor via Ethernet.
Explains connecting radar to 8000i/GB40 using a NMEA 0183 heading sensor.
Covers starting up the radar, selecting modes, and initial setup procedures.
Lists scanner, radar processor, and connection kits required for NX/M-Series displays.
Illustrates wiring and connection methods for Simrad NX and Northstar M-Series displays.
Explains how to set up the radar, including zero bearing, zero range, and antenna height.
Lists scanner, processor, and communication cables for 6000i/6100i systems.
Provides diagram and instructions for connecting the radar processor to the display unit.
Details connecting the radar communications cable (NS003107) to the junction box.
Explains setting up remote power control for 6000i/6100i with common or different power sources.
Covers turning the radar on/off, configuring communications, and adjusting appearance settings.
Details heading sensor requirements, disabling input, calibration, and tuning procedures.
Explains STC curve selection, trigger delay setting, and manual tuning procedures.
Covers heading calibration with/without sensor, and restoring factory settings.
Provides a detailed manual tuning procedure for specific situations where auto-tuning is insufficient.
Lists scanner, processor, and RIM300 interface module for Lowrance displays.
Details connecting the RIM 300 module and radar data cable to Lowrance displays.
Guides through initial radar setup, including communications port configuration and access.
Explains how to configure radar orientation, color scheme, trigger delay, and heading line.
Provides routine maintenance steps for keeping the radar system in good condition.
Details cleaning, lubricating, and servicing procedures for the radar scanner unit.
Suggests re-setting heading calibration annually and after major vessel changes.
Information on obtaining technical support, warranty, and contact details for assistance.
Covers common issues like no image, no scanner detected, or display showing only noise.
Addresses issues where the scanner fails to turn, involving motor or safety switch checks.
Provides steps to identify and reduce noise interference from other electronic equipment.
Checks for proper power supply, correct wiring, and inline fuse integrity for the radar processor.
Provides detailed dimensional drawings for the 2 kW radar scanner unit.
Provides detailed dimensional drawings for the 4 kW radar scanner unit.
Shows dimensional drawings for the Navico radar processor module.
Details the technical specifications for the 2 kW Navico radar system.
Details the technical specifications for the 4 kW Navico radar system.
To Next Page
