EasyManuals Logo
Home>NEC>Monitor>AccuSync LCD72VM

NEC AccuSync LCD72VM User Manual

NEC AccuSync LCD72VM
165 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #41 background imageLoading...
Page #41 background image
English
English-13
Specifications AccuSync LCD92VM Monitor
Monitor Specifications AccuSync LCD92VM Monitor Notes
LCD Module Diagonal: 48.3 cm/19 inches Active matrix; thin film transistor (TFT)
Viewable Image Size: 48.3 cm/19 inches liquid crystal display (LCD); 0.294 mm dot
Native Resolution (Pixel Count): 1280 x 1024 pitch; 250 cd/m
2
white luminance, 450:1
contrast ratio, typical.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms
Sync: Separate sync.TTL Level (Positive/Negative)
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Display Colours Analog input: 16,2 M Depends on display card used.
Synchronization Range Horizontal: 31.5 kHz to 81.1 kHz Automatically
Vertical: 55 Hz to 76 Hz Automatically
Viewing Angle Left/Right: -65°/+65°(CR>10)
Up/Down: -65°/+65°(CR>10)
Resolutions Supported Landscape: 720 x 400*
1
: VGA Some systems may not
640 x 480*
1
@ 60 Hz to 75 Hz support all modes listed.
800 x 600*
1
@ 56 Hz to 75 Hz
832 x 624*
1
@ 75 Hz
1024 x 768*
1
@ 60 Hz to 75 Hz
1152 x 864*
1
@ 70 Hz
1152 x 870*
1
@ 75 Hz NEC-Mitsubishi Electronics Display cites
1280 x 960*
1
@ 75 Hz recommended resolution at 60 Hz for
1280 x 1024 @ 60 Hz to 75 Hz................... optimal display performance.
Active Display Area Horizontal: 376.3 mm
Vertical: 301.1 mm
Speakers Practical Audio Output: 1.0 W + 1.0 W
Power Supply 100 - 240 V ~ 50/60 Hz
Power Consumption 40 W
Dimensions Landscape: 418 mm (W) x 427.8 mm (H) x 199.5 mm (D) (with stand)
418 mm (W) x 369.8 mm (H) x 68 mm (D) (without stand)
Weight 6.5 kg
Environmental Considerations
Operating Temperature: 5 °C to 35 °C
Humidity: 30% to 80%
Altitude: 0 to 3,048 m
Storage Temperature: -10 °C to +60 °C
Humidity: 10% to 85%
Altitude: 0 to 12,192 m
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.
NOTE: Technical specifications are subject to change without notice.

Other manuals for NEC AccuSync LCD72VM

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NEC AccuSync LCD72VM and is the answer not in the manual?

NEC AccuSync LCD72VM Specifications

General IconGeneral
BrandNEC
ModelAccuSync LCD72VM
CategoryMonitor
LanguageEnglish

Related product manuals