30
• Use the ▲ and ▼ buttons to select “MULTI MODE”,
then use the
䊴
and
䊳
buttons to choose from
“SINGLE”, “SIDE BY SIDE1~3” and “PICTURE
IN PICTURE (BOTTOM LEFT~TOP LEFT)”.
• Use the ▲ and ▼ buttons to select “MAIN”/ “SUB”
and “LEFT”/“RIGHT”, then use the
䊴
and
䊳
buttons
to choose from “VIDEO1~3”, “HD/DVD1~2” and
“RGB1~3”.
PROGRAM TIMER
EXIT
DATE
MON
TUE
SAT
*FRI
—
SAT
*
SEL.
RETURN
ADJ.ZOOM
ON
08 : 30
- - : - -
08 : 30
08 : 30
- - : - -
08 : 30
15 : 30
OFF
10 : 30
18 : 15
12 : 15
10 : 00
- - : - -
12 : 15
16 : 00
INPUT
MULTI
—
VIDEO1
HD/DVD1
—
VIDEO1
RGB1
FUNCTION
INVERSE
—
WHITE
—
—
WHITE
—
PICTURE IN PICTURE SIDE BY SIDE
PROGRAM TIMER
MULTI SCREEN SETTING
EXIT
MULTI MODE
: BOTTOM LEFT
INPUT MODE
MAIN
SUB
SEL.
RETURN
ADJ.
: RGB/PC1
: VIDEO1
MULTI REPEAT
Two repeat timers are available.
Each timer has MULTI MODE, WORK TIME and INPUT
MODE functions.
Example:
TIMER1 is set to display RGB1 (MAIN) and VIDEO1
(SUB) for 4 hours in picute-in-picture mode.
TIMER2 is set to display RGB3 (LEFT) and HD/DVD1
(RIGHT) for 2.5 hours in side-by-side mode.
On “MULTI REPEAT” of “TIMER”, select “ON”, then
press the MENU/ENTER button.
The “MULTI REPEAT TIMER” screen appears.
Adjust the items.
TIMER
EXIT
PRESENT TIME
PROGRAM
MULTI REPEAT
: OFF
: OFF
SEL.
RETURN
ADJ.
MULTI REPEAT TIMER
EXIT
1 MULTI MODE
WORK TIME
INPUT MODE
MAIN
SUB
2 MULTI MODE
WORK TIME
INPUT MODE
LEFT
RIGHT
: BTM LFT
: 04H00M
: RGB/PC1
: VIDEO1
: S BY S1
: 02H30M
: RGB/PC3
: HD/DVD1
SEL.
RETURN
ADJ.
Information
䡵 MULTI REPEAT settings
MULTI MODE: Set the input mode to be displayed
while the timer is on.
WORK TIME: Set the time duration of the display.
Time range is from 1 minutes to 4 hours and 15 minutes.
INPUT MODE: Set the signal that will be displayed
within the selected screen.
Select “MAIN” or “SUB” for “PICTURE IN PICTURE
(BTM LFT~TOP LFT)” and “LEFT” or “RIGHT” for
“S BY S1~3”. Only one signal is selected for
“SINGLE”.
* The two repeat timers run consecutively, i.e., Timer1–
Timer2–Timer1–Timer2.
* When both PROGRAM TIMER and MULTI REPEAT
TIMER are set, priority is given to PROGRAM TIMER.
PROGRAM TIMER
MULTI SCREEN SETTING
EXIT
MULTI MODE
: SIDE BY SIDE1
INPUT MODE
LEFT
RIGHT
SEL.
RETURN
ADJ.
: RGB/PC1
: VIDEO1
Setting the power on mode
This function sets the input mode at the time the power is
switched on.
Example: Setting “VIDEO2”
Set “ADVANCED OSM” to “ON” in the main menu (1/
2), then perform the following operations.
On “PWR. ON MODE” of “OPTION3” menu, select
“VIDEO2”.
The available inputs depend on the setting of input.
OPTION3
3 / 4
EXIT
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
NEXT PAGE
: VIDEO2
: OFF
: ON
: OFF
: ALL
SEL.
RETURN
ADJ.
Information
䡵 PWR. ON MODE settings
LAST: Last mode (the input that was last selected at
the time the power was switched off).
VIDEO1, 2, 3: VIDEO input mode.
RGB1, 2, 3: RGB input mode.
HD/DVD1, 2: HD/DVD input mode.
MULTI: Multi screen mode.
Follow the procedure used for PROGRAM TIMER. See
page 29.
Enabling/disabling the front panel controls
This function enables/disables the front panel controls.
Example: Setting “ON”
Set “ADVANCED OSM” to “ON” in the main menu (1/
2), then perform the following operations.
On “CONTROL LOCK” of “OPTION3” menu, select
“ON”, then press the MENU/ENTER button.
OPTION3
3 / 4
EXIT
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
NEXT PAGE
: LAST
: ON
: ON
: OFF
: ALL
SEL.
RETURN
ADJ.
Information
䡵 CONTROL LOCK settings
ON: Disables the buttons on the front panel.
OFF: Enables the buttons on the front panel.
* Even when the CONTROL LOCK is set, the POWER
switch will not be locked.
* This becomes effective when the on-screen menu goes
out.
To Next Page
Loading...
