HomeConnect en
25
Basic setting Possible settings Explanation
Network Connect to network
Disconnect from network
If you disconnect the appliance from the network, all network
information will be deleted. This setting is useful if you have
new login details for the router.
Connect to app - This setting initiates the connection between the HomeCon-
nectapp and the appliance.
Remote control On
Off
When this function is deactivated, all you can do is view the
appliance's operating status in the app.
When this function is activated, you can remotely start and
control the appliance.
Appliance information - The display shows information about the network or the appli-
ance.
17.3 Operating the appliance with the
HomeConnect app
When the Remote start function is activated, you can
use the HomeConnectapp to remotely configure the
appliance's settings and start it.
Note:Some operating modes can only be started on
the oven itself.
Requirements
¡ The appliance must be switched on.
¡ The appliance must be connected to your home net-
work and to the HomeConnectapp.
¡ To configure the appliance's settings using the
HomeConnectapp, "Remote control" must be
switched on in the basic settings. When the Remote
start function is deactivated, only the appliance's op-
erating statuses are displayed in the HomeCon-
nectapp.
1.
Press to switch the appliance on.
2.
Tap .
a The display will show the main menu.
3.
Use the or button to select "Remote start" .
4.
To switch on the Remote start function, tap .
a The display will show .
5.
Configure a setting in the HomeConnectapp and
send it to the appliance.
Notes
¡ If you open the appliance door within 15minutes
of activating the Remote start function or of the
set program ending, the Remote start function
will be deactivated.
¡ When you start the oven using the controls on
the appliance itself, the Remote start function is
activated automatically. You can use the
HomeConnectapp to adjust the settings or start
a new program.
17.4 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nectuser, have installed the app on your mobile device
and be connected to the HomeConnectserver.
As soon as a software update is available, you will be
informed via the HomeConnectapp and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the HomeConnectapp if you are in your
local area network. The HomeConnectapp will inform
you once installation is successful.
Notes
¡ You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡ We recommend that you install security updates as
soon as possible.
17.5 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the HomeConnect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip:For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com
17.6 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
HomeConnect server (initial registration):
¡ Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡ Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
¡ The current software and hardware version of your
appliance.
¡ Status of any previous reset to factory settings.
This initial registration prepares the HomeConnect
functions for use and is only required when you want to
use the HomeConnect functions for the first time.
Note:Please note that the HomeConnect functions
can only be utilised with the HomeConnect app. In-
formation on data protection can be retrieved in the
HomeConnect app.
To Next Page
Loading...
Need help?
General
