NETGEAR GS305Pv2 User Manual

Installation Guide
5-Port Gigabit Ethernet Unmanaged Switch
with 4-Ports PoE+ (63W) GS305Pv2
5-Port Gigabit Ethernet Unmanaged Switch
with 4-Ports PoE+ (83W) GS305PP
Package contents
• SwitchmodelGS305Pv2orGS305PP
• DCpoweradapter
• Detachablepowercable(variesbyregion)
• Wall-mountkitscrews
• Fourrubberfootpads
• Installationguide
Note: WerecommendthatyouuseaCategory5e(Cat5e)cableorahigher
ratedcableforGigabitEthernetconnections.
Thisswitchisdesignedforindooruseonly.Ifyouwanttoconnectittoadevice
locatedoutdoors,theoutdoordevicemustbeproperlygroundedandsurge
protected,andyoumustinstallanEthernetsurgeprotectorinlinebetweenthe
switchandtheoutdoordevice.Failuretodosocandamagetheswitch.
3. Connect to power and check the LEDs
Whenyouconnectthepoweradaptertotheswitchandplugthepowercable
intoanelectricaloutlet,theLEDsindicatethestatus.
ModelsGS305Pv2andGS305PPprovidePoE+orPoEpoweronports1–4upto
30WPoEtoeachport,withaPoEpowerbudgetof63Wand83Wrespectiveto
eachmodelacrossallactivePoEports.
LED
Description
PowerLED On.Theswitchisreceivingpower.
Off.Theswitchisnotreceivingpower.
Ports1–5
leftLED
On.1000Mbpslinkonthisport.

On.100Mbpsor10Mbpslinkonthisport.
Blinking.1000Mbpsactivityonthisport.
Blinking.100Mbpsor10Mbpsactivityonthisport.
Off.Nolinkisdetectedonthisport.
Ports1–4
rightLED
On.PoEisinuse.

On.PoEfault.
Off.PoEisnotinuseonthisport.
PoEMaxLED ThePoEMaxLEDindicatesthestatusofthePoEbudgetontheswitch:
Off.Sufcient.Morethan7WofPoEpowerisavailable.

On.Lessthan7WofPoEpowerisavailable.
Blinking.Atleastonceduringtheprevioustwominutes,less
than7WofPoEpowerwasavailable.
1. Register the switch
1. FromacomputerormobiledevicethatisconnectedtotheInternet,visit
my.netgear.com.
2. LogintoyourNETGEARaccount.
Note: Ifyoudon’thaveafreeNETGEARaccount,youcancreateone.
TheMyProductspagedisplays.
3. Fromthemenuontheleft,selectRegister a Product.
4. IntheSerial Numbereld,typetheserialnumberofyourswitch.
Theserialnumberis13digitslong.Itisprintedontheswitchlabel.
5. FromtheDate of Purchasemenu,selectthedatethatyoupurchasedthe
switch.
6. ClicktheREGISTERbutton.
YourswitchisregisteredtoyourNETGEARaccount.
AconrmationemailissenttoyourNETGEARaccountemailaddress.
2. Connect the switch
Sample connections
Accesspoint
Securitycameras
VoIPphone
RouterInternet
GS305PP
Internet
PoE+
Beforeconnectingthisswitchtooutdoorcablesordevices,see
https://kb.netgear.com/000057103 forsafetyandwarrantyinformation.

NETGEAR GS305Pv2 Specifications

General

Ports	5
PoE Ports	4
Switching Capacity	10 Gbps
Switch Type	Unmanaged
Weight	1.1 lb (0.5 kg)
Power Supply	External Power Adapter
Input Voltage	100-240V AC, 50/60 Hz
PoE Standards	IEEE 802.3af
Mounting	Desktop, Wall-mountable
Operating Temperature	0° to 40°C (32° to 104°F)
Storage Temperature	-20° to 70°C (-4° to 158°F)
Humidity	90% max, non-condensing
MAC Address Table Size	1K
Jumbo Frame Support	9, 216 bytes