NETGEAR XAVB5201 User Manual

Installation Guide
This symbol was placed in accordance with the European Union Directive
2002/96 on the Waste Electrical and Electronic Equipment (the WEEE
Directive). If disposed of within the European Union, this product should be
treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or
registered trademarks of NETGEAR, Inc. in the United States and/or other countries.
Information is subject to change without notice.Other brand and product names are
trademarks or registered trademarks of their respective holders. ©2012 by NETGEAR, Inc.
All rights reserved.
May 2012
LED and Button Descriptions
Item Description
Power
LED
• Solid green. The electrical power is on.
• Solid amber. The adapter is in power saving
mode.
• Blinking green. The adapter is in the process of
setting up security.
• Off. There is no electrical power.
Power-
line LED
• Solid. The adapter is connected to a Powerline
network.
• Off. The adapter has not found any other
compatible Powerline devices using the same
encryption key.
The Pick A Plug feature lets you pick the electri-
cal outlet with the strongest link rate, indicated by
the color displayed by the LED:
Green: Link
rate > 80
Mbps (Best)
Amber: Link rate
> 50 and < 80
Mbps (Better)
Red: Link
rate < 50
Mbps(Good)
Powerline LED
Power LED
Ethernet LED
Reset
Security
Ethernet port
Factory
button
Powerline 500 (2-pack)
XAVB5201
Troubleshooting Tips
Power LED is off Make sure that power is supplied to the electrical
outlet, and that the Powerline devices are not plugged
into an extension cord, power strip, or surge protector.
Power LED is
amber
Power saving mode occurs when the Ethernet LED is
off. This can occur when:
• The Ethernet cable is unplugged.
• The device connected through the Ethernet cable is
turned off.
• The adapter is idle for 10 minutes.
It returns to normal mode within 2 seconds once the
Ethernet link is up.
Powerline LED
is off
• If you have set network security, make sure that all
Power line devices are using the same encryption
key; see the online User Manual for details.
• Press the Reset button on each device for 1 second
to return the Powerline adapter to its factory default
settings.
Powerline LED
is amber or red
Move the Powerline device to a closer location.
Ethernet LED is
off
• Make sure that the Ethernet cables are working and
securely plugged into the devices.
• Press the Reset button on each device for 1 second
to return the Powerline adapter to its factory default
settings.
Package Contents
Warning: Do not press the Security button on the Powerline
adapter until installation is complete and the adapters are
communicating with each other (indicated by the blinking
Powerline LED). Pressing this button too soon can temporarily
disable Powerline communication. If this should occur, use the
Factory Reset button to return the Powerline adapter to its
factory default settings.
Ethernet
LED
• Solid. The Ethernet port is linked.
• Off. There is no Ethernet connection.
Security
button
After you plug in your new AV adapter, press the
Security button for 2 seconds, then press the
security button on one of the other AV adapters in
your existing network for 2 seconds. Both buttons
must be pressed within 2 minutes.
Note: The Security button does not work in power
saving mode (see “Power LED is amber” in the
Troubleshooting Tips table).
Factory
Reset
Press the Reset button for 1 second, then release
it to return the Powerline adapter to its factory
default settings.
Item Description
Powerline 500
Nano Adapters
Ethernet cables
In some regions,
a Resource CD is
included with your
product.

NETGEAR XAVB5201 Specifications

General

Interface	Ethernet
Connectivity technology	Wired
Ethernet LAN (RJ-45) ports	1
Chipset	-
Internal	No
Plug and Play	Yes
Product color	White
Cable length	2 m
Connector(s)	RJ-45
Dimensions (WxDxH)	66.8 x 33.8 x 54.9 mm
Cabling technology	10/100BaseT(X)
Networking standards	IEEE 802.3
Maximum data transfer rate	500 Mbit/s
Windows operating systems supported	Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Professional
Sustainability certificates	RoHS
Cables included	LAN (RJ-45)

Weight and Dimensions

Depth	33.8 mm
Width	66.8 mm
Height	54.9 mm
Weight	82 g

Summary

LED and Button Descriptions

Power LED Status

Details Power LED states: solid green (on), solid amber (power saving), blinking green (security setup), off (no power).

Powerline LED Status

Explains Powerline LED: solid (connected), off (no compatible devices found), or color-coded link rate.

Ethernet LED Status

Covers Ethernet LED: solid (linked), off (no connection).

Security Button Function

Explains the Security button function for pairing adapters, warning against premature use.

Factory Reset Button

Details the Factory Reset button function to restore default settings and its operation.

Troubleshooting Tips

Power LED Troubleshooting

Addresses Power LED being off by checking power supply and connections, noting power saving mode.

Powerline LED Troubleshooting

Troubleshoots Powerline LED off (security key mismatch, device off) or amber/red (move closer).

Ethernet LED Troubleshooting

Fixes Ethernet LED off by checking cables, connections, and device status.

Package Contents Overview

Safety Information

Technical Support