13
15
Part # Description Quantity
14
Assembly & Mounting Instructions
Cottage Picket Wings
- Please refer to the set of instructions which is
relevant to the product you have purchased.
- Read instructions through carefully before
beginning assembly.
- Identify each component from material list.
- When assembling components, place on a
non-abrasive surface to avoid scratches.
- Do not use excessive force when assembling
components.
- In the event of missing or defective parts,
please call our customer service department
General Information:
- Cordless drill with #2 Robertson bit
- Tape measure
- Level
- Shovel
- Pencil
Tools Required:
1 4” sq. x 54” Posts
2 2” x 3 1/2” x 44 1/2” Top rails
3 2” x 3 1/2” x 43 1/2” Bottom rails
4 7/8” x 3” x 29 1/4” Pickets
7/8” x 3” x 30” Pickets
7/8” x 3” x 31 1/2” Pickets
7/8” x 3” x 32 3/4” Pickets
7/8” x 3” x 34 1/4” Pickets
7/8” x 3” x 36 1/4” Pickets
7/8” x 3” x 38 1/2” Pickets
7/8” x 3” x 41” Pickets
5 4” sq. Post caps
6 4” sq. Trim caps
7 5” sq. Base moldings
8 2” x 3 1/2” Rail mount brackets
9 Hardware kit (Includes):
7/8” x 3” Picket caps
3/4” Self-tapping stainless screws
Rail end spacers (1/4” & 1/2”)
Tube of vinyl cement
2
2
2
4
2
2
2
2
2
2
2
2
2
2
8
18
32
4
1
- Two bags of pre-mix concrete *
* Recommended for extra stability.
* Wings designed for the Nantucket II Arbor,
but will also fit most other models.
Materials Included:
49”
44 1/2”
Materials (Optional): (Not Included)
Part 1
Part 3
(Fig. 1)
Product dimensions & Part
identification.
(Fig. 2)
Post layout for installation.
If you have any questions concerning the assembly or installation of this product and require assistance, please call our Customer service
department at 1-800-282-9346 (ext.#20), Weekdays from 8:00 am. to 4:00 pm. Eastern standard time.
If you have any comments or suggestions about our product or service, please let us know! Call: 1-800-282-9346 (ext.#24). or E-mail:
info@newenglandarbors.com
To learn more about us, visit us on the web at: www.newenglandarbors.com
Questions ? :
Part 5
16
Apply a bead of vinyl cement to the underside of each post cap
(part 5). To ensure proper attachment to the post, apply the
cement to all internal “contact” points of the cap. Place the caps
onto the end of each post and push down firmly, until the end of
the post “bottoms out” on the inside of the cap. Allow a few
minutes for the cement to cure.
Part 7
(In 1 box)
Picket cap
Apply a bead of vinyl cement to the inside walls of one of the
pickets. Insert a picket cap into the open end of the picket and
press down firmly. Allow a few minutes for the cement to cure.
Repeat this step for the remaining 17 pickets.
152”
49”
39”
Nantucket II
Arbor
Part 2
Part 4
Part 6
Part 8
44 1/2”
(arbor opening)
If you’re attaching the wings to an arbor with no base moldings,
follow the next two steps. Fasten the rail mount bracket to the
post, so that the bottom edge of the bracket measures approx. 4”
from the ground.
Insert a 1/2” rail end spacer into each bottom bracket as
illustrated. Note: The spacers (found in the hardware kit) are
only required when the arbor has no base moldings. The bottom
wing rail is shorter than the top because it normally attaches to a
base molding, so the spacer only acts as a “filler” when the base
molding is not present.
To Next Page
Need help?
General
