Nidec NE300-4T0900G/1100P Quick Start Guide

73 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Part Number：31019007

www.drive-setup.com

Quick Start Guide

NE200/NE300

Variable Speed AC drive

Table of Contents

Other manuals for Nidec NE300-4T0900G/1100P

User Manual244 pages

Questions and Answers:

J
jacobmoraAug 22, 2025
What to do if my Nidec NE300-4T0900G/1100P show motor overload?
- T
  Toni StevensAug 22, 2025
  If your Nidec DC Drives indicate a motor overload, several factors could be responsible. First, check the input power source for any abnormalities. Ensure the motor's rated current is correctly configured in the settings. If the V/F curve isn't suitable, adjust it along with the torque boosting performance. For motors consistently operating with heavy loads at low speeds, consider using a specialized electric motor. Also, verify that neither the motor nor the load is blocked or experiencing sudden, large load changes. Finally, if the motor power is insufficient, use a motor and drive with appropriate power ratings.
M
Miss Kelly WolfeAug 25, 2025
What causes over current in Nidec NE300-4T0900G/1100P DC Drives during acceleration and how to fix it?
- K
  Krista ThomasAug 25, 2025
  Overcurrent during acceleration in Nidec DC Drives can stem from a few reasons. If the acceleration time is too short, increase it. Also, check the input power source for low voltage. Finally, if the drive power rating is too small, choose a drive with higher capacity.
A
Amanda RobinsonAug 25, 2025
What causes over current at constant-speed in Nidec NE300-4T0900G/1100P?
- C
  cthomasAug 26, 2025
  If you're experiencing overcurrent at a constant speed with your Nidec DC Drives, several factors could be the cause. Check the load for any abnormal mutations. Also, verify the input power source isn't experiencing low voltage. Ensure your drive has sufficient power capacity. Finally, if you're using closed-loop vector control, inspect the encoder and its wiring for any sudden disconnections.
J
Justin BrownAug 27, 2025
What to do if Nidec NE300-4T0900G/1100P DC Drives show drive overload?
- M
  michael12Aug 27, 2025
  If your Nidec DC Drives are showing a drive overload, first check the input power source for low voltage. If the load is too heavy, select a drive with a bigger capacity. If the acceleration is too fast, increase the acceleration time. Also, avoid restarting the motor while it's still turning.
E
Elizabeth DiazAug 27, 2025
What causes over current in Nidec NE300-4T0900G/1100P DC Drives during deceleration?
- P
  Peter BaileyAug 27, 2025
  Overcurrent during deceleration in Nidec DC Drives can occur due to several reasons. If the deceleration time is too short, increase it. If there is a large load inertia, add suitable brake devices. Finally, if the drive power rating is too small, choose a higher capacity drive.
R
Ryan McdonaldAug 28, 2025
What to do if my Nidec DC Drives show over voltage in deceleration?
- S
  Shannon StarkAug 29, 2025
  If your Nidec DC Drives are showing an overvoltage during deceleration, the deceleration time may be too short, so increase it. Also, if the load inertia is large, add suitable brake devices.
L
luis82Aug 30, 2025
How to fix heat-sink over heat in Nidec NE300-4T0900G/1100P?
- L
  Lisa Mcdaniel DVMAug 30, 2025
  To resolve heat-sink overheating in Nidec DC Drives, first lower the ambient temperature. If the fan is damaged, replace it. Also, ensure the fan air duct is clear of any blockages.
R
Ryan LewisAug 31, 2025
What to do if my Nidec NE300-4T0900G/1100P show over voltage in constant speed?
- K
  Kelli HallAug 31, 2025
  If your Nidec DC Drives are showing an overvoltage at constant speed, first check the input power source for abnormalities. If the load inertia is large, add suitable braking devices.
W
Wendy ColeSep 2, 2025
What to do if my Nidec DC Drives show over Voltage in Acceleration?
- S
  Sarah HerreraSep 2, 2025
  If your Nidec DC Drives display an overvoltage during acceleration, it could be due to a too short acceleration time, so increase it. Another possible cause is an abnormal power supply, so check the input power source.
C
Carl DawsonSep 3, 2025
What to do if Nidec NE300-4T0900G/1100P DC Drives show fast current limit fault?
- J
  Jasmine EatonSep 3, 2025
  If your Nidec DC Drives are showing a fast current limit fault, it could be due to a load that is too large or a motor blocked to stall, so decrease the load and check the motor and mechanical part status. If the drive power rating is too small, choose a higher power drive. If the drive output circuit loop is grounded or short-circuited, remove the external fault.

Nidec NE300-4T0900G/1100P Specifications

General

Brand	Nidec
Model	NE300-4T0900G/1100P
Category	DC Drives
Language	English

Related product manuals

Nidec NE300-4T0300G/0370P

Nidec NE300-4T0750G/0900P

Nidec NE300-4T0055G/0075PB

Nidec NE300-4T0110G/0150PB

Nidec NE300-4T0150G/0185PB

Nidec NE300-4T0220G/0300PB

Nidec NE300-4T1320G/1600P-D

Nidec NE300-4T2000G/2200P-U

Nidec NE300-4T2800G/3150P-F

Nidec NE300-4T3550G/4000P-F

Nidec NE300-4T4500G/5000P-F