Nidec NE300-4T2800G/3150P-F Quick Start Guide

73 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Part Number：31019007

www.drive-setup.com

Quick Start Guide

NE200/NE300

Variable Speed AC drive

Table of Contents

Other manuals for Nidec NE300-4T2800G/3150P-F

User Manual244 pages

Questions and Answers:

J
Jacob PetersonAug 22, 2025
What to do if my Nidec NE300-4T2800G/3150P-F DC Drives show motor overload?
- C
  Christina MurrayAug 22, 2025
  If your Nidec DC Drives indicate a motor overload, several factors could be responsible. First, check the input power source for any abnormalities. Ensure the motor's rated current is correctly configured in the settings. If the V/F curve isn't suitable, adjust it along with the torque boosting performance. For motors consistently operating with heavy loads at low speeds, consider using a specialized electric motor. Also, verify that neither the motor nor the load is blocked or experiencing sudden, large load changes. Finally, if the motor power is insufficient, use a motor and drive with appropriate power ratings.
T
Tara KhanAug 25, 2025
What causes over current in Nidec NE300-4T2800G/3150P-F DC Drives during acceleration and how to fix it?
- M
  Michael PetersAug 25, 2025
  Overcurrent during acceleration in Nidec DC Drives can stem from a few reasons. If the acceleration time is too short, increase it. Also, check the input power source for low voltage. Finally, if the drive power rating is too small, choose a drive with higher capacity.
M
Matthew PetersonAug 25, 2025
What causes over current at constant-speed in Nidec NE300-4T2800G/3150P-F DC Drives?
- S
  Sarah CaseAug 26, 2025
  If you're experiencing overcurrent at a constant speed with your Nidec DC Drives, several factors could be the cause. Check the load for any abnormal mutations. Also, verify the input power source isn't experiencing low voltage. Ensure your drive has sufficient power capacity. Finally, if you're using closed-loop vector control, inspect the encoder and its wiring for any sudden disconnections.
L
Lori DeanAug 27, 2025
What to do if Nidec DC Drives show drive overload?
- T
  Tina RoblesAug 27, 2025
  If your Nidec DC Drives are showing a drive overload, first check the input power source for low voltage. If the load is too heavy, select a drive with a bigger capacity. If the acceleration is too fast, increase the acceleration time. Also, avoid restarting the motor while it's still turning.
T
Tammie SmithAug 27, 2025
What causes over current in Nidec NE300-4T2800G/3150P-F during deceleration?
- J
  Julie MartinAug 27, 2025
  Overcurrent during deceleration in Nidec DC Drives can occur due to several reasons. If the deceleration time is too short, increase it. If there is a large load inertia, add suitable brake devices. Finally, if the drive power rating is too small, choose a higher capacity drive.
J
Jason GonzalesAug 28, 2025
What to do if my Nidec DC Drives show over voltage in deceleration?
- K
  Kimberly Dalton DDSAug 29, 2025
  If your Nidec DC Drives are showing an overvoltage during deceleration, the deceleration time may be too short, so increase it. Also, if the load inertia is large, add suitable brake devices.
C
Caleb LongAug 30, 2025
How to fix heat-sink over heat in Nidec DC Drives?
- B
  Beth BennettAug 30, 2025
  To resolve heat-sink overheating in Nidec DC Drives, first lower the ambient temperature. If the fan is damaged, replace it. Also, ensure the fan air duct is clear of any blockages.
D
David CamposAug 31, 2025
What to do if my Nidec DC Drives show over voltage in constant speed?
- M
  maria56Aug 31, 2025
  If your Nidec DC Drives are showing an overvoltage at constant speed, first check the input power source for abnormalities. If the load inertia is large, add suitable braking devices.
C
Casey ColeSep 2, 2025
What to do if my Nidec NE300-4T2800G/3150P-F DC Drives show over Voltage in Acceleration?
- T
  Tammie FosterSep 2, 2025
  If your Nidec DC Drives display an overvoltage during acceleration, it could be due to a too short acceleration time, so increase it. Another possible cause is an abnormal power supply, so check the input power source.
A
April RiveraSep 3, 2025
What to do if Nidec NE300-4T2800G/3150P-F DC Drives show fast current limit fault?
- C
  crystalcameronSep 3, 2025
  If your Nidec DC Drives are showing a fast current limit fault, it could be due to a load that is too large or a motor blocked to stall, so decrease the load and check the motor and mechanical part status. If the drive power rating is too small, choose a higher power drive. If the drive output circuit loop is grounded or short-circuited, remove the external fault.

Nidec NE300-4T2800G/3150P-F Specifications

General

Output Current	2800A
Cooling Method	Forced air cooling
Input Voltage	3-phase, 380-480V AC
Speed Control Range	1:100
Control Method	Digital control
Protection Functions	Overcurrent, overvoltage, undervoltage, overtemperature, short circuit

Related product manuals

Nidec NE300-4T2000G/2200P-U

Nidec NE300-4T Series

Nidec NE300-4T0300G/0370P

Nidec NE300-4T0750G/0900P

Nidec NE300-4T0900G/1100P

Nidec NE300-4T0055G/0075PB

Nidec NE300-4T0110G/0150PB

Nidec NE300-4T0150G/0185PB

Nidec NE300-4T0220G/0300PB

Nidec NE300-4T1320G/1600P-D

Nidec NE300-4T3550G/4000P-F

Nidec NE300-4T4500G/5000P-F