Nilfisk-ALTO POSEIDON 5 User Manual (English)

Questions and Answers:

C
christopherjonesJul 26, 2025
What to do if the Nilfisk-ALTO Pressure Washer motor does not start?
- E
  Elaine LawsonJul 27, 2025
  If the Nilfisk-ALTO Pressure Washer motor doesn't start, check the plug, lead, and switch, and have them replaced by a skilled electrician if necessary. Also, verify the oil level and add oil if it's too low. Ensure the mains fuse is switched on. Finally, the overload protection may have been activated due to overheating or overloading; in this case, ensure that the mains voltage and the cleaner voltage are the same, switch off the cleaner, and allow it to cool for at least 3 minutes.
T
Taylor MurphyAug 1, 2025
What to do if my Nilfisk-ALTO Pressure Washer motor switches off?
- J
  James BentleyAug 1, 2025
  If the motor of your Nilfisk-ALTO Pressure Washer switches off, it could be due to the overload protection being activated because of overheating or overloading. Check that the mains voltage and the cleaner voltage are the same, then switch off the cleaner and allow it to cool for at least 3 minutes. Another possible cause is a dirty high-pressure nozzle, so change the high-pressure nozzle.
J
Jason McdonaldAug 5, 2025
What to do if the Nilfisk-ALTO POSEIDON 5 motor buzzes but doesn't start?
- P
  Patrick SwansonAug 5, 2025
  If the Nilfisk-ALTO Pressure Washer motor buzzes without starting, have the electrical connection checked because the mains voltage might be too low, or there could be a phase failure. Use lead with correct cross section or length, because incorrect cross-section or length of the extension lead can cause this problem. If the pump is blocked or frozen, contact the Nilfi sk-ALTO customer service.
R
Rebecca RiveraAug 11, 2025
Why is there a pressure drop in my Nilfisk-ALTO POSEIDON 5?
- S
  Steven EricksonAug 11, 2025
  A pressure drop in your Nilfisk-ALTO Pressure Washer might be due to air in the system; vent it by operating the spray gun several times at short intervals, or briefly operate the cleaner without the high-pressure hose. It could also be caused by a blocked or worn high-pressure nozzle, which you should clean or replace. Lastly, check if the detergent tank is empty and top it up or set the detergent to “0”.
S
Sandra ShannonAug 15, 2025
What causes pressure fluctuations in my Nilfisk-ALTO POSEIDON 5 Pressure Washer?
- A
  Ashlee GonzalesAug 15, 2025
  Pressure fluctuations in your Nilfisk-ALTO Pressure Washer can occur if the pump draws in air, which is only possible in suction mode, so check that the suction set is airtight. Another cause is a lack of water; ensure the water tap is open. The water inlet hose might be too long or have a cross-section that's too small, so use a water inlet hose that can provide the water flow (Q) defined for the max machine. Also, a blocked water filter can cause a lack of water; clean the water filter in the water connection, and never operate the machine without it.
T
Thomas MejiaAug 21, 2025
Why is my Nilfisk-ALTO POSEIDON 5 Pressure Washer not drawing in detergents?
- M
  matthew45Aug 21, 2025
  If your Nilfisk-ALTO Pressure Washer isn't drawing in detergents, first check if the detergent tank is empty and top it up. Ensure the cap on the FlexoPower-Plus nozzle head is set to low pressure. Also, verify that the double lance is adjusted to low pressure. Finally, the injector might be dirty, or the suction hose could be blocked; if so, clean them.

Nilfisk-ALTO POSEIDON 5 Specifications

General

Motor Power	5.5 kW
Weight	17.8 kg
Hose Length	10 m
Voltage	400 V
Frequency	50 Hz
Electric cable	5 m
Max. inlet temperature	60 °C
Ceramic pistons	Yes
Detergent tank	2.5 l
Water Flow	15 l/min
Voltage/phase/frequency	400 V / 3-phase / 50 Hz