9 10
ninjakitchen.com
PROGRAMMING THE DELAY BREW TIME
1 With Power on, press DELAY BREW.
The DELAY BREW button will illuminate
and the clock will flash “12:00” or the last
Delay Brew time that was set (Fig. 7).
2 While the clock is flashing, use the H and
M buttons to set the time you would like
the Delay Brew to begin. The AM or PM
indicator will illuminate on the left side
of the display as you are setting the
desired time.
3 Select desired brew style and selection
will illuminate (Fig. 8).
4 Once the time, brew size, and brew
type have been set, press the DELAY
BREW button again to activate, or wait
five seconds for the brew time to lock
in automatically. An audio signal will
indicate the brew time has been set,
and the DELAY BREW button will
remain illuminated.
NOTE: To deactivate the Delay Brew
cycle, press the DELAY BREW button
once more and the light on the button
will turn o. Any change to the selected
brew size or starting any other brew will
cancel the programmed Delay Brew.
Turning o the unit will also cancel the
Delay Brew.
5 Place the carafe under brew basket.
NOTE: The Ninja® Coee Brewer must
remain on for the Delay Brew function
to work. DO NOT power o after setting
the Delay Brew time.
Fig. 7
Fig. 8
Fig. 9
WARMING PLATE
The warming plate will turn on once the
brew has started. Press the STAY WARM
button after the brew to turn o the warming
plate (Fig. 9). You can turn the warming
plate back on by pressing the STAY WARM
button again. Wait until surface has cooled
completely before touching.
NOTE: DO NOT add additional water to
the reservoir when using the STAY WARM
function.
You can program the warming plate to stay
on for up to 4 hours.
1 Press and hold STAY WARM button until
the clock flashes, displaying the time at
which the warming plate is currently set
to turn o.
2 Quickly press the hour (H) or minute (M)
button to adjust the time up to 4 hours.
3 To lock in the new duration, press the
STAY WARM button again, or wait 5
seconds for it to lock in automatically.
CARE & MAINTENANCE
CLEANING AFTER A BREW
1 After each brew is complete and the
coee grounds have cooled, discard the
paper filter. Take out the removable filter
holder, rinse, and wash with soap
and
warm water.
2 We recommend cleaning your
carafe with warm, soapy water, or
placing it on the top rack of
your dishwasher. If you want
to clean the carafe more
thoroughly, we recommend
using a soft foam brush such as
the one shown to the right.
a Empty the water reservoir.
b Hand-wash with dish soap and
rinse or place on the top rack of
your dishwasher.
3 Unplug your unit and let the warming
plate cool before cleaning. Wipe down
with a soft cloth and warm water.
DO NOT immerse the base in water.
DESCALING YOUR
NINJA® COFFEE BREWER
1 Make sure the SMALL BATCH button
is not selected/illuminated and set the
empty carafe beneath the brew basket.
2 Use a descaling solution specifically
formulated for coeemaker cleaning and
follow the directions on the package.
Fill the water reservoir up to, but not
exceeding, the 12-Cup Line (60 fl. oz.).
OR
Add 16 oz. of white vinegar to the water
reservoir, then fill the rest of the reservoir
with water up to, but not exceeding, the
12-Cup Line (60fl. oz.).
3 Once the water reservoir is filled with
your cleaning solution and water mixture,
press the CLEAN button. The clean cycle
takes approximately 25–35 minutes. To
cancel the clean cycle, either press the
CLEAN button again or press the
Power button.
4 The unit will beep when the clean cycle
successfully completes. Refill the reservoir
with fresh water up to, but not exceeding,
the 12-Cup Line, and set the empty carafe
beneath the brew basket. Run a full Classic
Brew cycle with water only to remove any
cleaning solution that could aect the
flavor of your coee.
To Next Page
Loading...
Need help?
General
