4ninjakitchen.com3
ninjakitchen.com
COOKING WITH THE NINJA SIZZLE™ GRILL AND GRIDDLE
1 To install the grill or griddle grate, position it
over the base with the grease trap toward
the front. Place the cooking grate down
ensuring the sides align with the exterior
of the base.
2 Make sure the unit is plugged in, then turn the
dial to the desired temperature. The power
indicator light will illuminate.
3 Allow the grill to preheat with the lid closed for
7 minutes before cooking.
4 When preheat is complete, open the lid and
place ingredients on the grill grate.
5 Once ingredients are cooked to the desired
doneness, remove from the grill and turn the
dial until it clicks into the “OFF” position. The
power indicator light will turn o.
6 To remove the grill or griddle grate for
cleaning, ensure the dial is in the “OFF”
position, and the unit is unplugged and
has had sucient time to cool. Open the
lid and lift the cooking grate straight up by
grabbing the vertical walls along the edge of
the cooking surface.
NOTE: Ninja Sizzle Grill and Griddle can be
used with the lid open or closed.
NOTE: The griddle plate is not included on
all models.
INSTALLING AND REMOVING THE SPLATTER LID
CLEANING YOUR GRILL AND GRIDDLE
The unit should be cleaned thoroughly after
each use. Always let the appliance cool before
cleaning.
1 Unplug the unit from the wall outlet before
cleaning. Keep the lid open after removing
your food to allow the unit to cool quicker.
2 To prolong the nonstick coating of the grill
and griddle plates, we recommend hand-
washing in warm, soapy water then air or
towel-drying all parts. The splatter lid is
dishwasher safe.
3 If food residue or grease is stuck on the grill
grate, splatter lid, or any other removable
part, soak in warm, soapy water before
cleaning.
4 To clean the base heating unit of the grill,
use a damp, soapy cloth, then wipe with a
clean, damp cloth and dry thoroughly.
NOTE: NEVER use abrasive tools or cleaners.
NEVER immerse the main unit in water or any
other liquid. Do not place in dishwasher.
1 After allowing the unit to cool, remove the lid by opening it until it is approximately vertical
(Figure 1). Then lift the lid straight up out of the hinge base.
2
To install the lid, hold it vertically with the handle facing up and the hinge pivots over the hinge
base (Figure 2). Ensure that the flat sections of the hinge pivots are oriented vertically (Figure 3).
Lower the lid hinge pivots into the hinge base, then close the lid.
Figure 1 Figure 2 Figure 3
TROUBLESHOOTING GUIDE
• Why is the unit emitting smoke?
When using the Grill function, always select the recommended temperature setting. Recommended
settings can be found in the Quick Start Guide and in the Inspiration Guide. Make sure the splatter
shield is installed.
• Why did a circuit breaker trip while using the unit?
The unit uses 1450 watts of power, so it must be plugged into an outlet on a 15-amp circuit breaker.
Using an outlet on a 10-amp breaker will cause the breaker to trip. It is also important that the unit
be the only appliance plugged into an outlet when in use. To avoid tripping a breaker, make sure the
unit is the only appliance plugged into an outlet on a 15-amp breaker.
REPLACEMENT PARTS
ACCESSORIES FOR PURCHASE
To order additional parts and accessories, visit ninjaaccessories.com or contact Customer
Service at 1-877-646-5288. So we may better assist you, please register your product online at
registeryourninja.com and have the product on hand when you call.
We oer a suite of custom-made accessories for your Ninja Sizzle™ Grill and Griddle.
Visit ninjaaccessories.com to expand your capabilities and take your cooking to the next level.
To Next Page
Loading...
Need help?
General