What does Er 01 mean on Nonin WristOx2 3150 Medical Equipment?
If 'Er 01' is displayed on the LCD of your Nonin Medical Equipment, it indicates a device configuration memory failure. The device will revert to default settings (Spot-Check mode, 4-second sample rate). Use the nVISION software to change settings.
Why Nonin Medical Equipment does not record in Programmed mode?
If your Nonin device isn't recording in Programmed mode, it could be due to incorrectly set data collection start and stop times. Use the nVISION software to program the correct start and stop times. Alternatively, the clock settings may have been lost after replacing the batteries; use the nVISION software to reset the clock.
What to do if Nonin WristOx2 3150 shows a poor pulse signal?
If your Nonin Medical Equipment displays a poor pulse signal and the pulse strength indicator shows two bars or less, it could be due to an inadequate pulse signal or cold hands. Try repositioning or replacing the sensor, or place it on a different finger. If cold hands are the issue, warm the sensor application site.
Why is there no pulse display on my Nonin Medical Equipment?
Several factors might cause the absence of a pulse display on the pulse strength bar graph indicator of your Nonin device. * The sensor may be incorrectly applied, so refer to the sensor Instructions for Use for proper application. * There might be interference from blood flow restrictors like arterial catheters or blood pressure cuffs; try to reduce or eliminate the restriction. * Excess pressure from the sensor could be reducing circulation; check the sensor alignment, reposition it, and verify you're using the correct sensor size. * Excessive ambient light could also interfere; shield the sensor from the light source and check its alignment. Also, remove any fingernail polish or artificial nails if the sensor is applied to them.
How to fix Nonin WristOx2 3150 that will not activate?
If your Nonin Medical Equipment isn't turning on, there are several possible reasons. First, check that the batteries are correctly inserted and are not depleted; replace them if necessary. Ensure the sensor is properly connected. If the device is in Sensor Activation mode and has timed out, press the activation switch. Lastly, if the device is in Programmed mode, use the nVISION software to select Spot Check or Sensor Activation mode.
What does error Er 02 or 04 mean on Nonin Medical Equipment?
If Er 02 or Er 04 displays on the LCD of your Nonin Medical Equipment, the device has experienced a memory failure and you should contact Nonin Technical Service.
What does error Er 03 or 05 mean on Nonin Medical Equipment?
If error code Er 03 or Er 05 displays on the LCD of your Nonin Medical Equipment, the device has experienced a device failure. If the error code continues, contact Nonin Technical Service.
What does error Er 02 or Er 04 mean on Nonin WristOx2 3150 Medical Equipment?
If 'Er 02' or 'Er 04' is displayed on the LCD of your Nonin Medical Equipment, it indicates a device memory failure.
What does error Er 03 or Er 05 mean on Nonin WristOx2 3150 Medical Equipment?
If 'Er 03' or 'Er 05' is displayed on the LCD of your Nonin Medical Equipment, it indicates a device failure. The device memory is intact, but the device may have lost the most recent session or stored data.
General| Brand | Nonin |
|---|---|
| Model | WristOx2 3150 |
| Category | Medical Equipment |
| Language | English |
Describes the startup sequence and self-test of the device.
Details settings that can be programmed using nVISION software.
Step-by-step guide to access and change device settings via nVISION.
Steps to install the USB driver for Windows 7.
Steps to install the USB driver for Windows 8.
Steps to install the USB driver for Windows 10.
Lists available reusable pulse oximeter sensors.
Information on how to contact Nonin for service and support.
Details specific performance parameters of the oximeter.
To Next Page
