What to do if an error code appears on my Nonin Avant 9700 Medical Equipment?
If an error code appears, the Avant 9700 has encountered an error. First, turn the unit off and then back on again to remove the error code. If the error persists, disconnect all power (AC and battery), and then reconnect the power and turn the unit back on. If the error still persists, note the error code and contact your distributor or NONIN Customer Support.
How to fix a Nonin Medical Equipment device that will not activate?
If your Nonin device isn't activating, it might be due to several reasons: the device may have no power, so plug in the AC power supply. Also, the battery pack might be connected incorrectly, so check the battery pack connector orientation. If the battery pack is not charged, plug in the device AC power supply to charge it. Note that new battery packs must complete one charge/discharge/recharge cycle before the Battery LED displays the actual capacity.
What to do if a dash appears in the %SpO display on Nonin Avant 9700 Medical Equipment?
If a dash appears in the %SpO display, it indicates an inadequate signal from the finger. Try repositioning the sensor or applying it to a different finger, and keep the sensor motionless for at least 10 seconds. Warming the sensor application site may also help. The dash may also appear if the finger was removed from the sensor, so ensure proper placement.
Why can't I hear audible alarms when my Nonin Avant 9700 Medical Equipment unit is in Alarm mode?
If you can't hear audible alarms while the unit is in Alarm mode, the 2-minute Alarm Silence button may be activated. Press the Alarm Silence button to activate the alarm volume, or wait for 2 minutes, after which the alarm tones will automatically activate. Alternatively, if option switch 1 is in the UP position, the unit’s volume may be set to zero. Adjust the alarm volume, or return option switch 1 to the DOWN position if audible alarms are required.
What to do if a dash appears in the %SpO display on my Nonin Medical Equipment?
If a dash appears in the %SpO display, it indicates a poor signal from the digit is being detected or the digit was removed from the sensor. Try repositioning the digit or inserting a different digit, ensuring the sensor remains motionless for at least 10 seconds. If the digit was removed, reinsert it and keep the sensor motionless. If the issue persists, turn the unit off, check all connections, and retry.
Why does my Nonin Avant 9700 Medical Equipment show frequent pulse quality indications?
Frequent or steady pulse quality indications can occur due to excessive ambient light, application of the Avant 9700 to a polished or artificial fingernail, or excessive patient motion. Shield the sensor from the light source, apply the sensor to a finger without artificial or polished nails, and reduce patient motion.
How to fix no green pulse display on the bargraph of Nonin Avant 9700?
If you're unable to obtain a green pulse display on the bargraph, the patient's pulse strength might be low, or circulation is reduced because of excess pressure on the sensor, or the digit is cold. Try repositioning the digit or inserting a different digit, and keep the sensor motionless for at least 10 seconds. Allow the digit to rest comfortably without squeezing or pressing the sensor on a hard surface. Warm the digit by rubbing or covering with a blanket.
What to do if I still can't get a green pulse display on my Nonin Avant 9700 Medical Equipment?
If you are still unable to obtain a green pulse display, ensure the sensor is applied correctly. Possible interference from sources like arterial catheters, blood pressure cuffs, electrosurgical procedures, or infusion lines might be the cause. Reduce or eliminate any interference and ensure the sensor is not placed on the same arm being used for other patient therapies or diagnostics, such as a blood pressure cuff. Also, check that the red LED is illuminated in the digit insertion area and that the sensor is securely attached to the device.
Why won't my Nonin Medical Equipment Avant 9700 operate on batteries?
If the Avant 9700 will not operate on batteries, it could be due to several reasons: * The battery pack is inserted incorrectly. Check the battery pack connection. * The battery pack is not charged. Plug in the Avant 9700 AC Adapter to charge the battery pack. * The battery pack is inoperable. Contact your distributor or NONIN Customer Support for repair or replacement.
Why are there no audible alarms on my Nonin Avant 9700 Medical Equipment?
If the unit is in Alarm mode but no audible alarms can be heard, the 2-minute Alarm Silence button may be activated. Press the Alarm Silence button to re-engage alarm volume, or wait for two minutes—and alarm tones will automatically re-engage. Alternatively, DIP switch 1 might be in the UP position, and the unit’s volume is set to zero. Adjust the alarm volume, or return DIP switch 1 to the DOWN position if you desire audible alarms.
Critical safety precautions and contraindications for using the device.
Important considerations and potential risks associated with device operation.
Explanation of symbols used on the device and in the manual.
Overview of front panel layout, buttons, displays, and indicators.
Details on %SpO2, Pulse Rate displays, LEDs, and indicator descriptions.
Functionality of front panel buttons for operation and navigation.
Instructions for installing batteries and the serial port cover.
Steps for startup, sensor verification, and setting default parameters.
Core device operations like power, battery, display, and print-on-demand.
Managing custom settings, recalling previous configurations, and patient security mode.
Details on configuring the eight option switches for device behavior.
Description of the primary waveform display showing SpO2 and pulse rate.
How to view historical SpO2 and pulse rate data over 24 hours.
Analysis of stored data using histogram format and nurse call functionality.
Details on high priority alarms, their indicators, and default settings.
Information on medium priority, watchdog alarms, and alarm limit adjustments.
How to silence, recall, and manage alarm lock states.
Managing patient security mode and understanding error code descriptions.
Procedure for clearing specific error codes (06, 08, 10).
Details on data storage, management, and using nVISION software.
Options for real-time and print-on-demand data output.
Considerations for integrating the device with other medical systems.
Instructions for cleaning the device safely and effectively.
Information on obtaining replacement parts and accessories.
Solutions for device activation, pulse display, and signal issues.
Resolving SpO2 display problems and alarm/recording failures.
Procedures for returns and warranty details for the device.
Exclusionary statement regarding express and implied warranties.
Manufacturer's declarations, emissions, and immunity data.
Immunity test levels for ESD and transients.
Recommendations for separation distances from RF transmitters.
Information on signal loss handling and response times for SpO2 and pulse rate.
Summary of accuracy testing and principles of pulse oximetry operation.
Technical details for the oximeter, system, environment, and power.
Device classifications and electrical specs for nurse call output.
General| Type | Pulse Oximeter |
|---|---|
| Measurement Parameters | SpO2, Pulse Rate |
| Display | LED |
| Connectivity | USB |
| SpO2 Range | 0 to 100% |
| Battery Type | AA Alkaline |
| Data Storage | 72 hours of memory |
| Perfusion Index Range | 0.2 to 20% |
| Accuracy | ±2% SpO2 |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -20 to 60 °C |
| Humidity | 10% to 95% non-condensing |
To Next Page
